Alternatives and similar repositories for wisweep

Users that are interested in wisweep are comparing it to the libraries listed below

• bdring / PendantsForFluidNC
  Pendants for controlling FluidNC CNC firmware
  ☆41Updated 3 months ago
• MGX3D / EspDRO
  ESP32 DIY Digital Readout
  ☆99Updated 5 years ago
• Saur0o0n / PIDKiln
  Kiln PID controller based on Espressif Systems ESP32 chip board with Arduino IDE.
  ☆143Updated 7 months ago
• bdring / FluidDial
  A Pendant for FluidNC CNC Firmware
  ☆61Updated 3 weeks ago
• slimcdk / esphome-custom-components
  Drivers / components for ESPHome
  ☆45Updated 2 months ago
• ProjectsWithRed / auto-wire-stripper-cutter
  An automatic wire stripper and cutter, you simply choose some measurements on a screen and it will do it all for you.
  ☆80Updated 2 years ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆75Updated last year
• dronecz / ESP32-Reflow-Controller
  Reflow controller with ESP32 and TFT LCD on board.
  ☆68Updated 3 weeks ago
• maakbaas / esp32-soil-moisture-sensor
  Software and Gerber files for a simple soil moisture sensor using the ESP32 and a bistable status indicator.
  ☆37Updated 3 years ago
• Stutchbury / Manualmatic-Pendant
  The Manualmatic Pendant for LinuxCNC
  ☆50Updated 3 weeks ago
• karoria / grblTouch
  webUI optimized for 6 to 10 inch touch displays for grblHAL.
  ☆15Updated last year
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆50Updated 4 months ago
• AC8L / FluidNC-Pendant
  Pendant for FluidNC-powered devices over Wi-Fi using Websockets
  ☆25Updated 2 years ago
• nikhil-robinson / klipper_esp32
  Klipper_ESP32 is an implementation of the Klipper protocol for Espressif's ESP32 microcontroller set.
  ☆53Updated 4 months ago
• seeul8er / RepPanel_ESP32
  Alternative to PanelDue. Embedded UI for Duet & RepRap based 3D printers. Running on the ESP32. Optimized for 3.5" displays. WiFi or UART…
  ☆91Updated 2 years ago
• gadjet / Window-Door-sensor-Version-5
  Version 5 of the Window/Door sensor project this time with ultra low current consumption
  ☆64Updated last year
• rin67630 / Drok-Juntek-on-steroids
  Extend the possibilities of cheap digital power supplies with a WiFi module
  ☆59Updated last year
• markniu / PandaCAN
  CAN bus extruder, more resistant to noise,reduce a lot of wires for your 3D printer
  ☆113Updated last year
• ftobler / pick-plaz
  Open source pick and place machine
  ☆25Updated 10 months ago
• freeasabeer / SpaceMouse
  ☆26Updated 4 years ago
• makerbase-mks / MKS-TinyBee
  MKS TinyBee is a mainboard for 3d printing, based on ESP32 module
  ☆146Updated 2 years ago
• SasaKaranovic / DIY-Filament-Dryer
  DIY WiFi Filament dryer
  ☆164Updated last year
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆80Updated 2 years ago
• FYSETC / FYSETC-E4
  FYSETC Board - The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi …
  ☆67Updated 3 months ago
• drspangle / infidel-sensor
  Firmware, mechanical and electrical design files for the Inline Filament Diameter Estimator, Lowcost (InFiDEL).
  ☆189Updated 3 years ago
• MintyTrebor / moonNode
  A set of node-red nodes to interface with the Moonraker API for Klipper
  ☆18Updated last year
• zapta / ble_stepper_motor_analyzer
  A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
  ☆53Updated last year
• ProfBoots / V2.0-3D-Printed-RC-SkidSteer
  ☆40Updated last year
• naikymen / klipper-for-cnc
  Fork of the Klipper 3D-printer firmware, plus features for more general CNC.
  ☆116Updated this week
• JGAguado / Smart_Powermeter
  The Smart Powermeter is powered by a ESP32-S2, allowing the measurement up to 6 CT clamps for reading electric current and real-time disp…
  ☆90Updated 2 months ago