Alternatives and similar repositories for KiKit:

Users that are interested in KiKit are comparing it to the libraries listed below

• MariusHeier / magik_solder_paste_stencil_box
  Is it magik? Or is it just a 3d printed box for holding your solder stencils with automatic lifting and vacuum hold down?
  ☆33Updated 3 years ago
• makerstorage / pnpAssist
  PNPASSIST: A “SMART” BUILD PLATFORM FOR MANUAL PCB ASSEMBLY
  ☆42Updated 3 years ago
• bytesizedengineering / Solder-Reflow-Oven
  ☆33Updated last year
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆55Updated last year
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆126Updated this week
• opulo-inc / feeder
  Source for LumenPnP Feeders
  ☆109Updated this week
• UnexpectedMaker / vacuum-stencil-box
  ☆29Updated 3 years ago
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆69Updated 4 years ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆29Updated last year
• Neumi / tmc2209_devboard
  An Arduino shield to test the TMC2209 stepper motion controller by Trinamic.
  ☆34Updated last year
• EmanuelBender / HEX_POD
  Multi-sensor intelligent environmental Monitor
  ☆15Updated 9 months ago
• wntrblm / jellyfish-and-starfish
  ☆103Updated 2 years ago
• ioces / haptick
  a 6DOF force sensitive input device
  ☆39Updated last year
• ProjectsWithRed / auto-wire-stripper-cutter
  An automatic wire stripper and cutter, you simply choose some measurements on a screen and it will do it all for you.
  ☆56Updated last year
• kingoflolz / linear-actuator-hardware
  ☆59Updated 2 years ago
• sphawes / index
  This is the personal fork of the LumenPnP Repo for Stephen Hawes. For the official repo, go here: https://github.com/opulo-inc/lumenpnp
  ☆129Updated last year
• markmaker / PushPullFeeder
  All 3d-Printed Tape&Reel Feeder
  ☆74Updated 2 months ago
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆33Updated last year
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆53Updated 2 months ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆26Updated 9 months ago
• jduffy105 / HydraMeter_0.4
  Open source multimeter
  ☆92Updated 3 weeks ago
• G-EDM / G-EDM-v1-deprecated
  The G-EDM is a 4in1 electrical discharge machine that supports sinker EDM, EDM engraving, EDM drilling and Wire EDM operations. In the fu…
  ☆47Updated 4 months ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆144Updated last year
• makermoekoe / Stencil-Jig
  ☆159Updated 2 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆109Updated last year
• Lite3DP / Lite3DP-Gen-2
  MSLA 3D printer, ESP32 based, Arduino compatible
  ☆44Updated 2 months ago
• Rack-Robotics / Powercore-V1.0-Hardware
  CAD & Electronics for Powercore V1
  ☆147Updated last year
• aeonSolutions / AeonLabs-Solder-Reflow-Plate-PCB
  Solder Reflow Plate PCB
  ☆30Updated 11 months ago
• Rack-Robotics / EDMWeb
  EDM CAM software for generating EDM gcode
  ☆22Updated last year
• ghent360 / PrntrBoardV2
  32-bit 3D Printer controller board using STM32F407 and replaceable TMC2660/2209 stepper drivers.
  ☆39Updated 3 years ago