Alternatives and similar repositories for Blu-ray-Laser-Scanning-Microscope

Users that are interested in Blu-ray-Laser-Scanning-Microscope are comparing it to the libraries listed below

• atomic14 / kicad-coil-plugins
  Some simple plugins for generating stator coils in kicad
  ☆111Updated last year
• 0x23 / nmWave-Interferometer
  An Open Source Interferometer for Accurate Distance Measurements
  ☆94Updated 5 months ago
• opengalvo / OPAL
  Minimalistic FW for Processing GCode to Galvanometer signals
  ☆102Updated last year
• kingoflolz / linear-actuator-hardware
  ☆66Updated 3 years ago
• 0x23 / MicroManipulator
  An open source low-cost, easy-to-build XYZ Micro-Manipulator platform.
  ☆215Updated 5 months ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆41Updated 2 years ago
• upnalab / SonicSurface
  Generating Airborne Ultrasonic Amplitude Patterns Using an Open Hardware Phased Array
  ☆190Updated 5 months ago
• astuder / epc901
  Experiments with ESPROS epc901 1024x1 CCD line sensor, including a spectroscope.
  ☆56Updated 2 years ago
• marcoreps / laser_driver
  Energy efficient constant current diode laser driver
  ☆49Updated 7 years ago
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆77Updated 4 months ago
• Andrew-Dickinson / photonic-etcher
  Generate exposure masks for Anycubic printers from PCB Gerbers
  ☆102Updated last year
• Matthias-Wandel / caliper-interface
  Connecting cheap digital calipers to Raspberry Pi and decode readings
  ☆124Updated 11 months ago
• danjulio / tCam
  Thermal imaging cameras based on the ESP32 and Lepton 3.5
  ☆136Updated last year
• bairdd / Zyrus-Etcher
  Zyrus STM Tip Etching Machine
  ☆24Updated 2 years ago
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆67Updated 6 months ago
• kingoflolz / linear-actuator-firmware
  ☆31Updated 3 years ago
• NiklasHammerstone / GalvoStep
  Project for building a cheap galvo laser system using Stepper motors and widely available parts.
  ☆57Updated 2 years ago
• 0x23 / open-air-bearings
  Techniques and software to build, design and simulate air bearings
  ☆59Updated last year
• jduffy105 / HydraMeter_0.4
  Open source multimeter
  ☆152Updated last year
• sphawes / fiber-laser-pcb-fab
  Instructions and settings for fabricating PCBs on a fiber laser, namely the xTool F1 Ultra
  ☆134Updated last month
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆64Updated 2 years ago
• robin7331 / pixel-pump-mainboard
  ☆52Updated 2 years ago
• pavikonda / RaspberryPi_FPScope
  Fourier ptychographic microscope based on a Raspberry Pi. Publication: 10.1038/s41598-019-43845-9
  ☆37Updated 5 years ago
• wntrblm / jellyfish-and-starfish
  ☆110Updated 3 years ago
• coreWeaver / LC-Meter
  Open Source LC-Meter. All documentation included.
  ☆87Updated 3 years ago
• CentyLab / PicoPD
  Repo for PicoPD hardware/software and documentation
  ☆60Updated last year
• marcoreps / multiinstrumentalist
  Multi instrument datalogging platform
  ☆88Updated this week
• fasaxc / pico-bldc
  RP2040-based BLDC motor controller
  ☆43Updated last year
• 0x23 / QuietAirCompressor
  A small and quiet air compressor design using 3D printed parts where possible.
  ☆96Updated last year
• thethoughtemporium / sputteringsystem
  ☆145Updated 4 years ago