megasaturnv / HX-2S-JH20-JH10-reverse-engineered_aka-2S-10A-Balance-Li-ion-Protection-PCBLinks
Reverse engineered circuit board of the HX-2S-JH20 PCB . Aka 2S 10A w/Balance Li-ion BMS Protection Board.
☆38Updated 6 years ago
Alternatives and similar repositories for HX-2S-JH20-JH10-reverse-engineered_aka-2S-10A-Balance-Li-ion-Protection-PCB
Users that are interested in HX-2S-JH20-JH10-reverse-engineered_aka-2S-10A-Balance-Li-ion-Protection-PCB are comparing it to the libraries listed below
Sorting:
- Open Source LC-Meter. All documentation included.☆81Updated 3 years ago
- Simplified and optimized replacement controller for the low-cost W.E.P. 858D+ Hot Air Soldering Station☆14Updated 8 years ago
- DIY Electronic load for DCDC converter characterization☆50Updated 4 years ago
- Dual JBC T245 compatible 300W soldering station☆63Updated 4 years ago
- Semi-automatic 3D printable feeder for custom SMT Pick and Place machine☆50Updated 8 years ago
- Solder Reflow Plate PCB☆31Updated last year
- Custom firmware for the chinese ksger soldering iron controller☆171Updated 5 years ago
- JBC_SolderingStation☆88Updated last year
- Controller board (mosfet and thermistor control) for 12V heating ceramic element☆32Updated 4 years ago
- ST-Link Research☆24Updated 3 months ago
- A DIY soldering controller for JBC T245 handle & C245 tips☆40Updated last year
- An all-in-one Arduino compatible reflow controller powered by ATtiny1634R☆126Updated 3 years ago
- ☆105Updated last year
- Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.☆34Updated 2 years ago
- Reflow controller with ESP32 and TFT LCD on board.☆68Updated 3 weeks ago
- A DIY JBC T245 soldering iron station.☆42Updated 6 years ago
- ☆48Updated 7 years ago
- Component Tester in a Keychain☆74Updated 3 years ago
- Hot air rework controller for generic 858D / 8586 / 8858 / 852 / 878 / 858 hot air guns from China.☆31Updated 5 years ago
- 0816 SMT Automatic Feeder modified to work with the OpuloPNP. Custom firmware written for an arduino nano with a servo sheild can run 12 …☆15Updated 3 years ago
- Semi-automatic passive printable/castable feeder for LitePlacer☆59Updated 5 years ago
- tape puller/remover for 0816 automatic feeder☆21Updated 6 years ago
- 为DHO800/900系列示波器设计的电池包（Battery pack designed for DHO800/900 series oscilloscopes）☆80Updated last year
- Arduino STM32. Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 and STM3…☆40Updated 3 months ago
- This is V4 of the Arduino Spot Welder. An Arduino based Spot Welder for battery welding☆92Updated 2 months ago
- ☆17Updated 10 years ago
- HScope material repository☆160Updated last year
- All 3d-Printed Tape&Reel Feeder☆79Updated 8 months ago
- An improved ATMega328P with this cheap clone Logic Green LGT8F328P☆153Updated 2 years ago
- VC288 Volt-amp meter alternative firware. Targets the cheap DSN-VC288 volt-amp meter and the STM8S003F MCU.☆25Updated 4 years ago