Alternatives and similar repositories for Arduino-DRO-Linear-Scale-Interface

Users that are interested in Arduino-DRO-Linear-Scale-Interface are comparing it to the libraries listed below

• stephenhouser / Arduino-DRO
  Firmware for Arduino DRO with 4 Axis, Tachometer, Touch Probe (http://www.rysium.com/rysium.docs/)
  ☆11Updated last year
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆81Updated 5 months ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 10 months ago
• drandrewthomas / ESP32_GRBL_CNC_Wireless_Pendant
  A wireless GRBL CNC pendant project based on the ESP32 micro-controller
  ☆54Updated 4 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆79Updated 5 years ago
• dining-philosopher / litefeeder
  Semi-automatic passive printable/castable feeder for LitePlacer
  ☆59Updated 5 years ago
• nickshl / SmartPendant
  SmartPendant - a way to control grblHAL based CNC machine without PC
  ☆66Updated last month
• MakingStuffChannel / DigitalCalipers
  Source code and other files for reading values from digital calipers. See the project page for complete write up at http://makingstuff.in…
  ☆40Updated 8 years ago
• positron96 / cnc3018-offline-controller
  Open-source firmware for popular cnc3018 stm32-based offline controller
  ☆79Updated last year
• tenbaht / servo-motor-controller
  Porting the great SMC3 servo motor controller by Elm Chan to an ATmega328
  ☆19Updated 6 years ago
• jschoch / ESPels
  ESP32 electronic leadscrew for a lathe
  ☆26Updated last year
• wagiminator / ATtiny13-TinyTacho
  Simple RPM-Meter
  ☆57Updated 3 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆125Updated last month
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆63Updated 2 years ago
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 6 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆60Updated 3 weeks ago
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆35Updated 3 years ago
• jzolee / HAL2UDP
  External step generator and IO interface for LinuxCNC over Ethernet with dual-core ESP32 and W5500 modules.
  ☆30Updated last month
• paukstelis / dcservo
  Position control of DC motors
  ☆12Updated 6 years ago
• ftobler / pick-plaz
  Open source pick and place machine
  ☆27Updated last year
• S-LABc / MT6701-Arduino-Library
  Библиотека Arduino для магнитного датчика MT6701
  ☆10Updated last year
• microsmt / Microsmt-PNP-hardware
  All documents about making microsmt pnpboard
  ☆63Updated last month
• dronecz / ESP32-Reflow-Controller
  Reflow controller with ESP32 and TFT LCD on board.
  ☆69Updated 6 months ago
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆51Updated last year
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆153Updated last week
• alexavr2 / alexfeeder
  Semi-automatic 3D printable feeder for custom SMT Pick and Place machine
  ☆53Updated 9 years ago
• KaeptnBalu / Arduino_Spot_Welder_V4
  This is V4 of the Arduino Spot Welder. An Arduino based Spot Welder for battery welding
  ☆100Updated 8 months ago
• bdring / PendantsForFluidNC
  Pendants for controlling FluidNC CNC firmware
  ☆44Updated 9 months ago
• PhamDuyAnh / Arduino_Modbus_LCD_Mach3_01
  Mach3 write to Arduino UNO to view X & Y DRO and read external button via ModBus protocol
  ☆12Updated 6 years ago
• itohio / ESPReflow
  ESP8266 reflow controller
  ☆26Updated 3 years ago