ioelectro / arduino-hcs-programmerLinks
Programmer for HCS301 EEPROM Code Hopping using Arduino
☆13Updated last year
Alternatives and similar repositories for arduino-hcs-programmer
Users that are interested in arduino-hcs-programmer are comparing it to the libraries listed below
Sorting:
- STM32 HAL library for reading code from HCS301 433Mhz Keeloq☆21Updated 5 years ago
- HCS301 Keeloq Programming Example☆29Updated 5 years ago
- Arduino RF rolling code keeloq receiver☆30Updated last month
- STM32 HAL library for reading and sending code for Radio frequency (RF) barrier (Came, Nice) simple code 12, 24 bit and HCS301 with keelo…☆33Updated 6 years ago
- Monitor Canbus traffic☆133Updated 8 months ago
- Simple RFID Emulator / Cloner☆28Updated last year
- Get RF frequencies that are above the set threshold by hopping through a list of commonly used frequencies☆10Updated 2 years ago
- An open source application for programming HCS EEPROM Code Hopping. Support keeloq key generation from manufacturer code for Simple, Norm…☆25Updated 8 months ago
- With this tool, you can register entries of the CC1101 during operation read and change. You can switch to send or receive. Set the trans…☆48Updated 4 years ago
- Arduino library for TI CC1101. Supports the latest Arduino IDE and Platformio. Tested with AVR atmega328, stm32f103, nodeMCU and probably…☆54Updated last year
- Arduino library that provides an implementation of the NFC RFAL for ST25R3916 component☆15Updated 2 weeks ago
- BW16 (RTL8720DN) Module - Getting Started with Arduino☆52Updated 4 years ago
- [WIP] Leverage Flipper Zero SPI ports to interact with MCPXXXX and provide CANbus Sniss Knife inside your pocket. Kind of Linux's Canutil…☆42Updated 2 months ago
- CC1101 Low-Power Sub-1 GHz RF Transceiver driver for esp-idf☆80Updated 2 months ago
- ModBus RTU for Flipper Zero☆26Updated last month
- Project implementing the UDS protocol on an STM32 microcontroller, with CAN communication for diagnostics and UART for testing and debugg…☆30Updated last year
- Analyze frequencies using CC1101☆31Updated last year
- A ESP32 based interface between CAN-bus and IoT environments.☆47Updated 2 years ago
- Presence detection using RTL8720DN 2.4G/5G Dual Bands Wifi Module☆41Updated 2 years ago
- An ESP32 CAN 2.0B library☆74Updated 7 months ago
- ECU emulator by ESP32 with TJA1050 for OBD2 print test☆63Updated last year
- ESP8266 / ESP32 / Arduino driver lib for using the great TI C1101 transceiver☆108Updated last month
- Arduino support for SAM D|L|C (M0+ and M4F). It adds support for new devices like the D51, SAMR34, L21, C21, and D11. It also adds new cl…☆10Updated last year
- A WHC CH32V003 debugger/flasher tool in Flipper Zero☆25Updated last year
- T-HMI board is used to interface various kinds of sensors like RYUW122 UWB module☆21Updated 11 months ago
- RadioSniffer 433/315 MHz☆20Updated 4 years ago
- Remote Control for barriers based on Arduino☆42Updated 3 years ago
- WT32-SC01-PLUS Module With SubGhz, Wifi and Bluetooth - Using CC1101, Able to play .sub files from the FlipperZero - Protocol Analysis, E…☆95Updated 3 months ago
- Flipper Zero alternative built for ESP32-S3☆14Updated 2 years ago
- cydOS is just another ESP32-2432S028R launcher....☆26Updated 7 months ago