Alternatives and similar repositories for OpenTrickler

Users that are interested in OpenTrickler are comparing it to the libraries listed below

• eamars / OpenTrickler-RP2040-Controller
  OpenTrickler controller application on RP2040 platform
  ☆19Updated this week
• zapta / ble_stepper_motor_analyzer
  A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
  ☆53Updated last year
• liutas4x4 / IR-probe_byDC42
  Differential IR Z probe for 3D printer
  ☆13Updated 5 years ago
• EmanuelBender / HEX_POD
  Multi-sensor intelligent environmental Monitor
  ☆17Updated last year
• freeasabeer / SpaceMouse
  ☆26Updated 4 years ago
• bigtreetech / BIGTREETECH-TMC5160-V1.0
  The TMC5160 contains the complete intelligence which is required to drive a motor. Receiving target positions the TMC5160 manages motor m…
  ☆65Updated 6 years ago
• Berkays / ReflowPlate
  Hardware & Firmware for a solder reflow plate PCB
  ☆24Updated last year
• Cooper-8pTX / Valentine-ECM-Mod
  A Configurable Electrochemical Machining Modification
  ☆18Updated 3 years ago
• bigtreetech / BIGTREETECH-TMC2130-V2.0
  Configuration:CFG microsteps: Up to 1/256 microPlyer: 1/256 Logic Voltage VI0: 3-5V Motor Voltage : 5.5-46V Motor Phase Current: 1.2…
  ☆15Updated 6 years ago
• nickshl / SmartPendant
  SmartPendant - a way to control grblHAL based CNC machine without PC
  ☆54Updated last month
• IvDm / Z-probe-on-smd-resistors-2512
  Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.
  ☆141Updated 5 years ago
• nikhil-robinson / klipper_esp32
  Klipper_ESP32 is an implementation of the Klipper protocol for Espressif's ESP32 microcontroller set.
  ☆50Updated 4 months ago
• MGX3D / EspDRO
  ESP32 DIY Digital Readout
  ☆99Updated 5 years ago
• luc-github / ESP3D-TFT
  ESP3D Firmware for ESP32 based TFT
  ☆46Updated 3 months ago
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆57Updated 7 months ago
• bdring / FluidDial
  A Pendant for FluidNC CNC Firmware
  ☆61Updated 3 weeks ago
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆72Updated 5 years ago
• markniu / PandaZHU
  3D printer control board based on ESP32,support 8 Driver motors.
  ☆80Updated 2 years ago
• zapta / simple_stepper_motor_analyzer
  A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…
  ☆152Updated 2 years ago
• Shortcircuitboards / PCB-CNC
  DIY Printed small PCB CNC for fast Prototyping
  ☆46Updated 4 years ago
• Saur0o0n / PIDKiln
  Kiln PID controller based on Espressif Systems ESP32 chip board with Arduino IDE.
  ☆143Updated 7 months ago
• markniu / PandaCAN
  CAN bus extruder, more resistant to noise,reduce a lot of wires for your 3D printer
  ☆113Updated last year
• prusa3d / Buddy-board-MINI-PCB
  ☆57Updated 2 years ago
• danjulio / Geiger-Counter
  Alpha-Beta-Gamma Geiger Counter with GUI
  ☆32Updated last year
• bigtreetech / BIGTREETECH-TMC2225-V1.0
  The TMC2225 are ultra-silent motor driver ICs for two-phase stepper motors.
  ☆13Updated 5 years ago
• polihedron / DIY-Reflow-Oven
  DIY Reflow Oven, mcu: STM32F103 dev board, Display: Nextion Basic 3.5", PID controller.
  ☆37Updated 3 years ago
• ProfBoots / V2.0-3D-Printed-RC-SkidSteer
  ☆40Updated last year
• Aus3D / z-probe
  Aus3D IR Z-Probe Source Files
  ☆10Updated 6 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆50Updated 3 months ago
• bdring / PendantsForFluidNC
  Pendants for controlling FluidNC CNC firmware
  ☆41Updated 3 months ago