Alternatives and similar repositories for mbot:

Users that are interested in mbot are comparing it to the libraries listed below

• bobricius / 2.5D-stepper-motor
  It is compatible with standard stepper motor diver, cnc or GRBL shield, direct replacement of X-Y stepper motors.
  ☆27Updated 5 years ago
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 5 years ago
• RaD / SolderPaste14M2
  Solder Paste Dispenser
  ☆18Updated 10 years ago
• makerstorage / pnpAssist
  PNPASSIST: A “SMART” BUILD PLATFORM FOR MANUAL PCB ASSEMBLY
  ☆42Updated 3 years ago
• BETZtechnik / ICEpick--Direct-drive-pick-and-place-head
  Pick and Place head with dual nozzles
  ☆39Updated 5 years ago
• openKolibri / klais-16
  Sixteen Segment Display in the Klais range.
  ☆55Updated 4 years ago
• kingoflolz / linear-actuator-hardware
  ☆60Updated 2 years ago
• bdring / PSoC_Grbl
  PSoc5 Port of Grbl CNC Controller
  ☆36Updated 8 years ago
• openpnp / mica-feeder
  Automatic SMT Tape Feeder by Pham Thang
  ☆19Updated 7 years ago
• technoblogy / tiny-function-generator
  A signal generator based on an ATtiny85 that generates a range of different waveforms
  ☆31Updated 5 years ago
• arturo182 / serpente_hw
  ☆35Updated 5 years ago
• SG-O / MiniFeedPCB
  Main PCB for automated SMT Feeder
  ☆10Updated 4 years ago
• felixstorm / Creality_Ender_3_ESP32_Board
  ☆55Updated 3 years ago
• ccadic / esp32reflow
  Small prototype of ESP32 Reflow controller
  ☆14Updated 3 years ago
• beast-devices / ant2-usb-c-lipo-charger
  Tiniest USB-C LiPo charger
  ☆34Updated 2 years ago
• Scavenger18 / RepoPNP
  Files concering PAIND PNP Feeder
  ☆23Updated 6 years ago
• wagiminator / ATtiny85-TinyLoad
  Electronic Dummy Load
  ☆47Updated 2 years ago
• bobc / kicad-utils
  Various utilities for KiCad
  ☆18Updated 5 years ago
• xpix / XDisPlace
  XDisplace are a complete solution to mill, dispense solder paste and pixk and place components to a pcb in one process!
  ☆12Updated 7 years ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated last month
• fluidfred / powerlolu
  High Power Pololu Board based on A4989 - can be connected to RAMPS Pololu port
  ☆30Updated 10 years ago
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆34Updated 2 years ago
• Cohesion3D / Cohesion3D-ReMix
  ☆13Updated 8 years ago
• cinderblock / 3-Phase-Driver
  Hardware design for a 3 Phase BLDC controller
  ☆57Updated 5 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆76Updated 4 years ago
• dining-philosopher / litefeeder
  Semi-automatic passive printable/castable feeder for LitePlacer
  ☆58Updated 5 years ago
• ErichStyger / McuOpenPnP_Machine
  Repository for the McuOnEclipse OpenPnP machine
  ☆64Updated 4 years ago
• MitkoDyakov / Calipatron
  I design my own digital caliper based on STM32F103C8T6 blue pill.
  ☆30Updated 5 months ago
• dasaki / nanoReflowController
  Reflow Oven Controller. See below for more information.
  ☆79Updated 5 years ago
• wagiminator / ATtiny13-TinyTacho
  Simple RPM-Meter
  ☆55Updated 2 years ago