Alternatives and similar repositories for ShushEngine

Users that are interested in ShushEngine are comparing it to the libraries listed below

• kingoflolz / linear-actuator-hardware
  ☆66Updated 3 years ago
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆166Updated last week
• TkkrLab / LinearMotor
  Diy Linear Motor
  ☆117Updated 4 years ago
• linuxcnc-ethercat / linuxcnc-ethercat
  LinuxCNC EtherCAT HAL driver
  ☆70Updated last month
• IdeaPropulsionSystems / CoolEpicyclicGearing
  Some resources for designing a special high-ratio planetary gearing system.
  ☆28Updated 7 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆62Updated last month
• makerbase-motor / MKS-SERVO42D-57D
  Makerbase MKS SERVO57D NEMA23 closed loop stepper motor Driver FOC quiet and efficient RS485 / CAN
  ☆67Updated last month
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆96Updated 7 months ago
• 0x23 / MicroManipulator
  An open source low-cost, easy-to-build XYZ Micro-Manipulator platform.
  ☆215Updated 5 months ago
• MetalMusings / MyOwnEtherCATDevice
  Documentation accompanying the "Make My Own EtherCAT device" video serie on Youtube.
  ☆82Updated 3 months ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆101Updated last week
• prusa3d / Buddy-board-MINI-PCB
  ☆60Updated 2 years ago
• multigcs / riocore
  riocore
  ☆67Updated this week
• BETZtechnik / ICEpick--Direct-drive-pick-and-place-head
  Pick and Place head with dual nozzles
  ☆39Updated 5 years ago
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆82Updated last year
• tommag / TMC5160_Arduino
  Arduino library for Trinamic TMC5160 stepper motor driver
  ☆83Updated last year
• markmaker / PushPullFeeder
  All 3d-Printed Tape&Reel Feeder
  ☆82Updated last year
• grblHAL / drivers
  Driver overview
  ☆39Updated 2 months ago
• scottalford75 / LinuxCNC-on-RPi
  ☆28Updated 5 years ago
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆74Updated 4 months ago
• roTechnic / CycloidalDesign
  ☆24Updated 3 years ago
• makerstorage / pnpAssist
  PNPASSIST: A “SMART” BUILD PLATFORM FOR MANUAL PCB ASSEMBLY
  ☆44Updated 4 years ago
• iforce2d / weenyPRU
  LinuxCNC component and firmware for Raspberry Pi to communicate with a STM32 microcontroller.
  ☆67Updated 6 months ago
• uStepper / uStepperS
  ☆53Updated 2 years ago
• hasenbanck / heteromycin
  A 3D printer board using a powerfull STM32 MCU, TMC5160/TMC2160 driver and a Raspberry Pi or compatible SBC
  ☆40Updated 5 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆127Updated last month
• atomic14 / kicad-coil-plugins
  Some simple plugins for generating stator coils in kicad
  ☆111Updated last year
• wezhunter / ESP32_LinuxCNC_MotionController_RealTime
  ESP32 hardware based real-time LinuxCNC motion controller
  ☆52Updated last year
• Peter-van-Tol / LiteX-CNC
  Generic CNC firmware and driver for FPGA cards which are supported by LiteX
  ☆77Updated 3 months ago