Alternatives and similar repositories for MiniFeedPCB:

Users that are interested in MiniFeedPCB are comparing it to the libraries listed below

• openpnp / mica-feeder
  Automatic SMT Tape Feeder by Pham Thang
  ☆19Updated 7 years ago
• issus / NEMA8-Juki-Tool-Changer
  Pick and Place tool changer nozzle to hold Juki 500 series nozzles on a NEMA8 hollow shaft motor
  ☆28Updated 8 years ago
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 5 years ago
• RaD / SolderPaste14M2
  Solder Paste Dispenser
  ☆18Updated 10 years ago
• richard-sim / openpnp-linear-rails
  An OpenPnP compatible SMT pick and place machine with linear rails based on Anthony Webb's build on hackaday.io.
  ☆13Updated 8 years ago
• OpenPanzerProject / Scout-ESC
  Dual motor serial controller - ATmega 328 MCU with VNH5019 motor drivers
  ☆15Updated 3 months ago
• Cohesion3D / Cohesion3D-ReMix
  ☆13Updated 8 years ago
• osresearch / servostep
  Closed loop servo control for stepper motors
  ☆10Updated 9 years ago
• fugalster / Smart-BLDC-Commutator-Hardware
  ☆15Updated 10 years ago
• koendv / SerialWireOutput
  Serial Wire Output (SWO) library for STM32duino arm Arduinos
  ☆21Updated last year
• atc1441 / CH55xOneClickCompiler
  CH551 to CH554 One Click SDCC Compiler
  ☆21Updated 3 years ago
• tom-biskupic / LabPSU
  Open Source Lab Power Supply
  ☆27Updated 3 years ago
• koendv / paste_dispenser
  Stepper motor controller for solder paste dispensers
  ☆30Updated 4 years ago
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆33Updated 2 years ago
• dining-philosopher / litefeeder
  Semi-automatic passive printable/castable feeder for LitePlacer
  ☆57Updated 4 years ago
• paltatech / half-bridge
  TO247 half bridge module for EVs
  ☆15Updated 6 years ago
• mgineer85 / sFeeder
  Parametric Feeder Design, load in OpenSCAD to make yours.
  ☆19Updated 9 months ago
• geniekobayashi / juki_nozzle_changer
  OpenPnP project
  ☆17Updated 8 years ago
• BETZtechnik / ICEpick--Direct-drive-pick-and-place-head
  Pick and Place head with dual nozzles
  ☆39Updated 4 years ago
• kaktus85 / MightyWattR3
  Resources for MightyWatt R3 electronic load
  ☆31Updated last year
• LKbrilliant / Solder-Paste-Dispenser
  Automated device to apply solder paste onto a PCB without using a stencil.
  ☆11Updated 3 years ago
• LibreSolar / 5uh-dc-lisn
  5uH DC LISN (-10 dB attenuation)
  ☆16Updated 5 years ago
• fluidfred / powerlolu
  High Power Pololu Board based on A4989 - can be connected to RAMPS Pololu port
  ☆30Updated 10 years ago
• terjeio / CNC_Breakout_Nucleo64
  CNC breakout for STM324F411 and ST32F446 development boards
  ☆20Updated last year
• Kurokesu / SCE2-GRBL
  Kurokesu motion controller SCE2-M module GRBL based firmware
  ☆16Updated last month
• bertrik / ElectronicLoad
  Arduino software for an electronically controlled load, based on a STM32 microcontroller
  ☆21Updated 4 years ago
• estechnical / reflowOvenController
  ESTechnical Reflow Oven Controller source code and instructions
  ☆47Updated 10 years ago
• tenbaht / servo-motor-controller
  Porting the great SMC3 servo motor controller by Elm Chan to an ATmega328
  ☆17Updated 5 years ago
• jankae / battery-sim
  A voltage source imitating the behaviour of a battery
  ☆11Updated 5 years ago
• kirberich / gerber_to_scad_service
  Simple django project to allow converting gerber files to 3d printable scad solder stencils
  ☆11Updated 8 years ago