Alternatives and similar repositories for DeepKarasR:

Users that are interested in DeepKarasR are comparing it to the libraries listed below

• Chiffa-C3 / Shark-Extruder
  Экструдер разработанный для замены стандартного на принтере FBG6
  ☆23Updated last year
• evgs / FBG6-Klipper
  ☆14Updated last month
• FB-G6 / Marlin
  Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin inst…
  ☆75Updated 7 months ago
• evgs / kross-pi-hat
  RPI/OPI Hat board for FB Ghost6 and Reborn2 touchscreens
  ☆15Updated last year
• Sergey1560 / Marlin_FB4S
  Marlin 2.0 for Flying Bear 4S/5
  ☆225Updated 11 months ago
• Tombraider2006 / K1
  creality k1 klipper
  ☆95Updated last week
• Sergey1560 / fb4s_howto
  Howto
  ☆78Updated last year
• Tombraider2006 / klipperFB6
  flyingbear ghost 6 klipper
  ☆369Updated this week
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆233Updated 2 years ago
• CODeRUS / klipper_config
  ☆28Updated 10 months ago
• pavluchenkor / iDryerController
  ☆24Updated last month
• evgs / OrangePi3Lts
  ☆12Updated last week
• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆97Updated this week
• Technarrus / Klipper_FBG6
  ☆22Updated 2 years ago
• dmitry-sorkin / Marlin_FB5_K3D
  Marlin 2.0 for Flying Bear 4S
  ☆52Updated 3 years ago
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆99Updated 2 years ago
• xreef / MKS_WIFI_upgrade_with_BeePrint_web_interface
  Firmware for MKS WiFi module from Makerbase with BeePrint Web Interface, tested with Flying Bear Ghost 4/5/6 Reborn Flsun
  ☆73Updated 3 months ago
• ArtificalSUN / MKS-WIFI_PS_uploader
  Simple G-code file uploader for 3D-printers equipped with MKS-WIFI module
  ☆55Updated last year
• oducceu / klipper_configs
  ☆36Updated 6 months ago
• Roman-RV78 / Nalivator
  ☆22Updated 2 years ago
• dmitry-sorkin / k3d-accuracy-test
  FDM 3D Print accuracy test
  ☆29Updated 2 years ago
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆58Updated last year
• vladimir-poleh / klipper-config
  ☆10Updated last year
• mvbasov / PETCTL
  Another variant of PET Pull (https://3deshnik.ru/forum/viewtopic.php?f=37&t=986) project controller
  ☆27Updated 2 years ago
• VICLER / GyverDrink
  Наливатор на Arduino
  ☆38Updated 3 years ago
• Andy-Big / Marlin_FB_Reborn
  MarlinRB - 3D Printer Firmware based on Marlin 3D v2.1, for Flyingbear Reborn with MKS Robin Nano v1.1, MKS Robin Nano v1.3, MKS Robin Na…
  ☆23Updated last year
• cryoz / K1_tenso_manual
  ☆27Updated 8 months ago
• AlexGyver / GyverLamp2
  Огненная лампа v2
  ☆162Updated last year
• AlexanderPro29 / OctoPrint-RU-LangPack
  RUssian LangPack for OctoPrint
  ☆17Updated last year
• gknapp / ghost6
  FlyingBear Ghost 6 3D Printer notes
  ☆14Updated 4 months ago