Peej11 / mainsail-installer
Automated install script for Klipper Mainsail and all dependencies
☆0Updated 4 years ago
Alternatives and similar repositories for mainsail-installer:
Users that are interested in mainsail-installer are comparing it to the libraries listed below
- ☆18Updated 4 months ago
- The closed-loop drive is to feedback the rotation angle of the stepping motor to the control panel, compare the distance that needs to be…☆21Updated last year
- ☆16Updated 5 years ago
- The TMC5160 contains the complete intelligence which is required to drive a motor. Receiving target positions the TMC5160 manages motor m…☆59Updated 5 years ago
- TMC2208 single-axis stepper motor drive chip, power tube built-in drive current 1.4A peak current 2A, voltage range 4.75V-36V, 256 subdiv…☆13Updated 5 years ago
- Configuration: CFG/SPI microsteps: Up to 1/256 microPlyer: 1/256 Logic Voltage VI0: 3-5V Motor Voltage : 5.5-46V Motor Phase Current…☆14Updated 5 years ago
- Klipper config for CR-10S Printer☆10Updated 5 years ago
- ☆31Updated 4 years ago
- Direct Drive Dual Gear Lightweight Extruder☆34Updated 2 years ago
- SMuFF Hardware Interface Firmware☆10Updated 5 years ago
- Stronger frame, Light weight component and easier to maintenance☆31Updated last year
- GTR V1.0 Stepper Driver Jumper Configuration Manual☆18Updated 4 years ago
- A completely new web interface for the Duet electronics☆13Updated 4 years ago
- Configuration:CFG microsteps: Up to 1/256 microPlyer: 1/256 Logic Voltage VI0: 3-5V Motor Voltage : 5.5-46V Motor Phase Current: 1.2…☆15Updated 5 years ago
- It's the Voron V1.6, but better! Now with linear rails for XY and a fully enclosable design.☆17Updated 3 years ago
- ☆43Updated 4 years ago
- BIGTREETECH TFT24-V1.1 is a small volume ultra-clear 3D printer display board. It can work in two modes. The board is launched by the 3D …☆52Updated 5 years ago
- A 6:1 Bowden and Direct Drive Extruder Platform☆24Updated 4 years ago
- TMC2209 is an ultra-silent motor driver IC for two-phase stepper motors. Its continuous drive current is 2A and peak current is 2.8A. Com…☆24Updated 5 years ago
- ☆23Updated 4 years ago
- This is the official repository for the TurboCAN controller board, designed specifically for the Voron AfterBurner toolhead but can also …☆78Updated 3 years ago
- ☆23Updated last week
- Smart Effector for delta printers.☆25Updated last month
- Arduino STM32. Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 boards☆16Updated 4 years ago
- A port of the BigTreetech Touchscreen Firmware for Marlin 3d printer boards- Added support for Makerbase MKS TFT28/MKSTFT32, should not b…☆34Updated 4 years ago
- ☆70Updated 6 months ago
- MKS SGEN is a powerful 32-bit 3D printer control board with LPC1769. Support Marlin2.0, Smoothieware. Support MKS LCD12864 and MKS TFT To…☆40Updated 4 years ago
- The closed-loop drive is to feedback the rotation angle of the stepping motor to the control panel, compare the distance that needs to be…☆113Updated 3 years ago
- CorEssentials is an open source corexy 3D printer.☆26Updated 3 years ago
- An ongoing remix of BLV's legendary MGN cube 3D printer☆17Updated 3 years ago