GadgetAngel / GTR-V1.0-Stepper-Driver-Jumper-Configuration-ManualLinks
GTR V1.0 Stepper Driver Jumper Configuration Manual
☆18Updated 4 years ago
Alternatives and similar repositories for GTR-V1.0-Stepper-Driver-Jumper-Configuration-Manual
Users that are interested in GTR-V1.0-Stepper-Driver-Jumper-Configuration-Manual are comparing it to the libraries listed below
Sorting:
- BIGTREETECH GTR V1.0 motherboard is a high-performance 3D printer main control board with the core controller STM32F407IGT6, which was la…☆93Updated 4 years ago
- BTT EXP MOT V1.0、BTT RRF WiFi V1.0、BTT EEPROM V1.0☆76Updated 2 years ago
- BIGTREETECH Relay V1.2 is an upgrade of the original (BIGTREETECH V1.0). After upgrading, a small MCU was added on the module to make the…☆137Updated 4 years ago
- This is a repository of BIGTREETECH bootloaders. The originals are stored under the bootloader_bin/backed_up_original_bootloaders/ direc…☆133Updated 3 years ago
- BigTree Technology Co., Ltd. developed this power failure module to detect a power failure during printing and ensuring the print can be …☆92Updated 5 years ago
- BigTree Technology Co., Ltd. developed this module for the use on firmware flashing, serial port debugging and so on.☆51Updated 5 years ago
- ☆60Updated 2 years ago
- Gcode model preview icon☆139Updated last year
- This library contains all the open source materials of BIGTREETECH touch screen hardware.☆189Updated 2 months ago
- ☆171Updated this week
- Mods for BLV Cube☆42Updated 2 years ago
- MKS H43 is a 4.3-inch high-definition IPS display with a resolution of 800*480 and uses a capacitive touch screen. This is a high-end scr…☆35Updated 3 years ago
- TMC2209 is an ultra-silent motor driver IC for two-phase stepper motors. Its continuous drive current is 2A and peak current is 2.8A. Com…☆222Updated 6 years ago
- A 3D Preview Tool☆26Updated 5 years ago
- ☆205Updated 3 years ago
- TMC2209 is an ultra-silent motor driver IC for two-phase stepper motors. Its continuous drive current is 2A and peak current is 2.8A. Com…☆24Updated 6 years ago
- support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1☆25Updated 5 years ago
- ☆307Updated last year
- support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1☆37Updated 10 months ago
- ☆85Updated 4 years ago
- Klipper is a 3d-printer firmware☆76Updated last week
- ☆77Updated 6 months ago
- OctoBTT☆161Updated 4 years ago
- Beta SKR V1.4 firmware for the Prusa MK3s Bear☆76Updated 4 years ago
- 3D-Printer TFT Preview and Replace icon☆25Updated 5 years ago
- Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.☆42Updated 5 years ago
- Pebble Wiper for Tool Changing 3D Printers☆120Updated 3 years ago
- ☆45Updated 2 years ago
- OO C++ RepRap Firmware☆265Updated 2 weeks ago
- Configurations for Marlin Firmware☆40Updated 4 years ago