MirageC79 / FilamentDryer_ControllerLinks
Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.
☆42Updated 5 years ago
Alternatives and similar repositories for FilamentDryer_Controller
Users that are interested in FilamentDryer_Controller are comparing it to the libraries listed below
Sorting:
- Mods for BLV Cube☆42Updated 2 years ago
- Beta SKR V1.4 firmware for the Prusa MK3s Bear☆76Updated 5 years ago
- Pebble Wiper for Tool Changing 3D Printers☆120Updated 3 years ago
- This is a repository of BIGTREETECH bootloaders. The originals are stored under the bootloader_bin/backed_up_original_bootloaders/ direc…☆134Updated 3 years ago
- RepRapFirmware configuration and macros to drive the Enraged Rabbit Carrot Feeder☆39Updated 2 years ago
- DIY WiFi Filament dryer☆169Updated last year
- Klipper config for CR-10S Printer☆10Updated 5 years ago
- Extensions and Themes for ESP3D-WEBUI v3☆13Updated 5 months ago
- BTT EXP MOT V1.0、BTT RRF WiFi V1.0、BTT EEPROM V1.0☆76Updated 2 years ago
- MLM IDEX is a mod for BLV MGN CUBE Project☆27Updated 3 years ago
- GTR V1.0 Stepper Driver Jumper Configuration Manual☆18Updated 4 years ago
- BIGTREETECH GTR V1.0 motherboard is a high-performance 3D printer main control board with the core controller STM32F407IGT6, which was la…☆93Updated 4 years ago
- Light, small and efficient extruder based on the popular Bondtech BMG.☆136Updated last year
- Klipper is a 3d-printer firmware☆77Updated last week
- This is the official repository for the TurboCAN controller board, designed specifically for the Voron AfterBurner toolhead but can also …☆79Updated 4 years ago
- This is my project to enable serial (UART) connected BigTreeTech-TouchScreens with Klipper by emulating anything it needs with macros.☆36Updated 11 months ago
- Firmware, mechanical and electrical design files for the Inline Filament Diameter Estimator, Lowcost (InFiDEL).☆195Updated 4 years ago
- Latest version of the SMuFF firmware to be compiled in PlatformIO☆215Updated last year
- CoreXY 3d Printer from Roy Berntsen☆113Updated 2 years ago
- support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1☆25Updated 5 years ago
- Direct Drive Dual Gear Lightweight Extruder☆37Updated 3 years ago
- A completely new web interface for the Duet electronics☆13Updated 4 years ago
- Muldex - REP-RAP IDEX 3D Printer☆123Updated last year
- Custom firmware for the SKR Bear Project. Go through the branches to find a firmware matching your setup.☆79Updated 3 years ago
- FYSETC Kit - Voron-Trident kit☆26Updated 3 years ago
- ☆95Updated last month
- Printed version of the Vz-Printhead☆147Updated 10 months ago
- Controlling LEDs from Klipper using LED Control from jackw01. This repository contains the needed files and an installation script.☆37Updated 3 years ago
- Stronger frame, Light weight component and easier to maintenance☆31Updated 2 years ago
- BIGTREETECH Relay V1.2 is an upgrade of the original (BIGTREETECH V1.0). After upgrading, a small MCU was added on the module to make the…☆139Updated 4 years ago