Alternatives and similar repositories for RedBot:

Users that are interested in RedBot are comparing it to the libraries listed below

• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆99Updated last month
• Sergey1560 / fb4s_howto
  Howto
  ☆77Updated last year
• ArtificalSUN / MKS-WIFI_PS_uploader
  Simple G-code file uploader for 3D-printers equipped with MKS-WIFI module
  ☆56Updated 2 years ago
• mvbasov / PETCTL
  Another variant of PET Pull (https://3deshnik.ru/forum/viewtopic.php?f=37&t=986) project controller
  ☆30Updated 2 years ago
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆102Updated 2 years ago
• pavluchenkor / iDryerController
  ☆44Updated last week
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆240Updated 2 years ago
• CODeRUS / klipper_config
  ☆28Updated last year
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆59Updated last year
• silver-alx / sbc
  Popular SBC linux images
  ☆28Updated 3 months ago
• gknapp / ghost6
  FlyingBear Ghost 6 3D Printer notes
  ☆16Updated 8 months ago
• AlexanderPro29 / OctoPrint-RU-LangPack
  RUssian LangPack for OctoPrint
  ☆19Updated last year
• dmitry-sorkin / Marlin_FB5_K3D
  Marlin 2.0 for Flying Bear 4S
  ☆51Updated 3 years ago
• jmz52 / MKS-Robin-Bootloader
  ☆12Updated 6 years ago
• makerbase-mks / MKS-WIFI
  MKS TFT WIFI and MKS ROBIN WIFI , share the same firmware. Support MKS Robin series board and MKS TFT series board, for cloud printing an…
  ☆95Updated 3 years ago
• Skiff2 / SkiffDRO
  Проект самодельного DRO
  ☆27Updated 2 years ago
• Andy-Big / Marlin_FB_Reborn
  MarlinRB - 3D Printer Firmware based on Marlin 3D v2.1, for Flyingbear Reborn with MKS Robin Nano v1.1, MKS Robin Nano v1.3, MKS Robin Na…
  ☆23Updated last year
• bigtreetech / BIGTREETECH-SKR-MINI-V1.1
  ARM Cortex-M3 series STM32F103RCT6 chip with 32-bit CPU 72MHz. Equipped with highly modular open source firmware Marlin2.0, convenient…
  ☆35Updated 4 years ago
• PrintMakerLab / mks-wifi-plugin
  MKS wifi plugin for Cura
  ☆142Updated last year
• gotchau / GBot-Tiny-Mark-II
  ☆32Updated 4 months ago
• pscrespo / Morpheus-STM32
  A small 3D printer controller board for use with a "blue pill" STM32F1 generic board. Inspired on http://reprap.org/wiki/SinapTec
  ☆73Updated 5 years ago
• Sergey1560 / Marlin_FB4S
  Marlin 2.0 for Flying Bear 4S/5
  ☆227Updated last year
• oducceu / klipper_configs
  ☆36Updated 9 months ago
• ursoft / Marlin
  Для владельцев Ulti Steel SKR 1.3 Fysetc Mini 12864 (но не только - некоторые изменения универсальны)
  ☆14Updated 4 years ago
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆21Updated last year
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆245Updated 2 years ago
• jmz52 / Marlin
  Optimized firmware for RepRap 3D printers based on the Arduino platform.
  ☆17Updated last year
• cryoz / K1_tenso_manual
  ☆30Updated 11 months ago
• HamsterTime-r / SpotWelder
  Точечная контактная сварка для аккумуляторов 18650 на Arduino
  ☆27Updated 4 years ago
• xreef / MKS_WIFI_upgrade_with_BeePrint_web_interface
  Firmware for MKS WiFi module from Makerbase with BeePrint Web Interface, tested with Flying Bear Ghost 4/5/6 Reborn Flsun
  ☆73Updated 6 months ago