Alternatives and similar repositories for creality-k1-max-xy-rails-mod:

Users that are interested in creality-k1-max-xy-rails-mod are comparing it to the libraries listed below

• K1-Klipper / installer_script_k1_and_max
  ☆53Updated 9 months ago
• ballaswag / k1-discovery
  Self discovered technical details for the Creality K1 printer
  ☆39Updated last year
• cryoz / K1_tenso_manual
  ☆28Updated 10 months ago
• pellcorp / creality
  ☆60Updated this week
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆85Updated last year
• fbeltrao-br / mksts35
  ☆71Updated last year
• freakydude / klipper-serial-btt
  This is my project to enable serial (UART) connected BigTreeTech-TouchScreens with Klipper by emulating anything it needs with macros.
  ☆28Updated 3 months ago
• Gliptopolis / WLED_Klipper
  A simple How-To for integrating LEDs with your Klipper/Moonraker machine
  ☆89Updated 2 years ago
• redrathnure / armbian-mkspi
  Armbian Linux Build Framework
  ☆112Updated last month
• tlace17 / K1-Linear-Rail-Gantry
  Linear Rail Gantry Conversion Mod for Creality K1 Series Printers
  ☆113Updated 2 months ago
• bassamanator / rp2040-zero-adxl345-klipper
  Instructions on how to connect your ADXL345 to your host Raspberry Pi via a RP2040-Zero
  ☆47Updated last year
• teeminus / NoTouchScreenFirmware
  Stripped down version of BIGTREETECH-TouchScreenFirmware which only supports ST7920 emulation (Marlin Mode)
  ☆157Updated 2 years ago
• CroXY3D / Sailfin-Extruder
  A lightweight compact extruder with 5:1 gearing using BMG dual drive
  ☆242Updated 2 years ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆31Updated last year
• jjsch-dev / filament_dryer_rp2040
  Heats and dries wet filaments to improve print quality and longevity.
  ☆21Updated last year
• willngton / 3DPrinterConfig
  My 3D Printers Configuration backup - Marlin and Klipper
  ☆44Updated 2 years ago
• maz0r / klipper_canbus
  guide on setting up canbus in klipper
  ☆199Updated last year
• bcmob / BIGTREETECH-TouchScreenFirmware
  support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1
  ☆25Updated 4 years ago
• VICLER / Moli-Extruder
  The most lightweight BMG dual drive filament extruder
  ☆46Updated 3 years ago
• armysolo / BLV-Cube
  Mods for BLV Cube
  ☆42Updated 2 years ago
• worksasintended / klipper_linear_movement_analysis
  ☆73Updated last year
• 11chrisadams11 / Klipper-WS281x_LED_Status
  Use WS281x LED strips with Klipper
  ☆52Updated 2 years ago
• makerbase-mks / MKS-SKIPR
  MKS SKIPR is an all-in-one board launched by Makerbase for running Klipper. It integrates the RK3328 SOC running the Klipper host and the…
  ☆111Updated 2 years ago
• bigtreetech / CB2
  The official repo for the BTT Pi2 and CB2
  ☆90Updated this week
• dmbutyugin / klipper
  Klipper is a 3d-printer firmware
  ☆75Updated last week
• CODeRUS / klipper_config
  ☆28Updated last year
• Stephan3 / dwc2-for-klipper-socket
  dwc2-for-klipper using klippers unixsocket
  ☆86Updated 3 years ago
• condottab / Roborock-CPAP
  CPAP cooling system using a Roborock fan
  ☆95Updated last year
• VzBoT3D / Vz-Printhead-Printed
  Printed version of the Vz-Printhead
  ☆138Updated 2 months ago
• D3vil-Design / K1-Max-Manta-Conversion
  ☆21Updated 7 months ago