Alternatives and similar repositories for nRF24-Esk8-Remote

Users that are interested in nRF24-Esk8-Remote are comparing it to the libraries listed below

• SolidGeek / nRF24-Esk8-Remote
  A remote used to control an electric skateboard
  ☆139Updated 5 years ago
• makerbase-mks / MKS-DLC
  MKS DLC support grbl firmware, can use Laser mode and CNC mode,support connect MKS TFT24/32/35 and TFT_CNC firmware support lasering and …
  ☆107Updated 4 years ago
• msglazer / Anti-Spark_Switch
  personal improvements/changes to the vedder antispark switch
  ☆67Updated 7 years ago
• uStepper / uStepper-RobotArm-Rev3
  uStepper Robot Arm STL files and instruction Revision 3
  ☆94Updated 8 years ago
• mstrens / grbl_controller_esp32
  grbl controller for esp32
  ☆203Updated 2 years ago
• shamansystems / Cheap-FOCer
  BLDC Motor Controller based on the VESC 4.12 hardware
  ☆74Updated 5 years ago
• maplerainresearch / MRR_ESPE
  MRR ESPE 3D printer control board
  ☆38Updated 6 years ago
• gcobos / grblesp
  GRBL ported to ESP8266, using up to 8 axis. No arduino involved
  ☆59Updated 8 months ago
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆90Updated 3 years ago
• TheDIYGuy999 / Micro_RC_Receiver
  An Atmega328P based 2.4GHz receiver with integrated TB6612FNG motor driver. PWM and SBUS outputs.
  ☆152Updated last year
• tmrttmrt / opentx
  OpenTX custom firmware for Transmitters
  ☆55Updated 5 years ago
• makerbase-mks / MKS-SERVO42B
  MKS SERVO42B is 3d printer closed loop stepper motor NEMA17 MKS SERVO42 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆181Updated 4 years ago
• mactep8 / SBus_Decoder
  S.Bus to PWM/PPM decoder
  ☆26Updated 11 years ago
• StefanMeGit / FeatherM0-Esk8-Remote
  ☆10Updated 6 years ago
• hackaday3D / marlin_stm32
  stm32 for marlin 1.1.9
  ☆53Updated 6 years ago
• DarrenLouw / SBUS
  Arduino library for the Futaba SBUS protocol
  ☆31Updated 7 years ago
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆74Updated 5 years ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆81Updated 5 months ago
• cruwaller / elrs_handset
  Custom DIY dual band (900/2400MHz) transmitter (handset) based on ExpressLRS.
  ☆69Updated 2 years ago
• uStepper / uStepperS
  ☆53Updated 2 years ago
• RollingGecko / VescUartControl
  Arduino library to interface with the VESC bldc over UART.
  ☆152Updated 4 years ago
• vedderb / SparkSwitch
  Active precharce circuit with optional switch input
  ☆51Updated 10 years ago
• makerbase-mks / MKS-Robin
  MKS Robin is a powerful 32-bit 3D printer control board with STM32F103ZET6 . Support Marlin2.0. Support MKS Robin TFT24/28/32... Screens.…
  ☆137Updated 4 years ago
• swanepoeljan / TrueStep
  The closed-loop drive is to feedback the rotation angle of the stepping motor to the control panel, compare the distance that needs to be…
  ☆21Updated 2 years ago
• JyeSmith / dshot-esc-tester
  Thrust stand data logger utilising the dshot600 protocol and ESC telemetry.
  ☆98Updated 3 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆80Updated 5 years ago
• FYSETC / FYSETC-E4
  FYSETC Board - The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi …
  ☆73Updated 10 months ago
• simon-jouet / ESP32Controller
  ESP32-based 3D printer controller
  ☆132Updated 4 years ago
• night-ghost / open-headtracker
  Automatically exported from code.google.com/p/open-headtracker and made some changes
  ☆11Updated 8 years ago
• bdring / 4_Axis_SPI_CNC
  4 Axis CNC Controller for Grbl_ESP32
  ☆69Updated 5 years ago