Alternatives and similar repositories for ARDUINO-SMD-REWORK-STATION:

Users that are interested in ARDUINO-SMD-REWORK-STATION are comparing it to the libraries listed below

• Muny / DIY-JBC-T245-Station
  A DIY JBC T245 soldering iron station.
  ☆42Updated 6 years ago
• acbaruth / 898D
  Combo_Hot_Air_Soldering_Station
  ☆11Updated 4 years ago
• lbthomsen / st-link
  ST-Link Research
  ☆22Updated last month
• sfrwmaker / TFT_Rework_station
  Soldering and rework station with TFT ili9341 display absed on stm32
  ☆21Updated 3 months ago
• ghent360 / RTD-2660-Programmer
  Realtek RTD2660/2662 programmer
  ☆105Updated 7 years ago
• mister-grumbler / w1209-firmware
  The functional eqivalent to the original firmware of "Digital Thermostat Module Model XH-W1209".
  ☆40Updated 6 years ago
• sfrwmaker / hakko_t12
  The hakko T12 digital controller on atmega328
  ☆66Updated 3 years ago
• IOsetting / hk32f030m-template
  HSXP HK32F030M template project for GNU Arm Embedded Toolchain
  ☆32Updated last year
• foldvarid93 / JBC_SolderingStation
  JBC_SolderingStation
  ☆88Updated last year
• stevstrong / Arduino_STM32
  Arduino STM32. Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 and STM3…
  ☆39Updated 2 months ago
• gavinlyonsrepo / LCR_meter
  LCR meter project. An Inductance, Capacitance and Resistance meter, Arduino NANO(v3) based.
  ☆87Updated last year
• akshaybaweja / component-tester-oled
  Component Tester in a Keychain
  ☆72Updated 2 years ago
• Upcycle-Electronics / DSN-VC288
  ☆45Updated 6 years ago
• pscrespo / Morpheus-STM32
  A small 3D printer controller board for use with a "blue pill" STM32F1 generic board. Inspired on http://reprap.org/wiki/SinapTec
  ☆71Updated 4 years ago
• cocus / vc288-alt-fw
  VC288 Volt-amp meter alternative firware. Targets the cheap DSN-VC288 volt-amp meter and the STM8S003F MCU.
  ☆24Updated 3 years ago
• wagiminator / ATtiny13-TinySolder
  T12 Quick Heating Soldering Station
  ☆83Updated 2 years ago
• dungjk / grbl-stm32
  An open source, embedded, high performance g-code-parser and CNC milling controller. This is a port of GRBL 1.1 to STM32F10X target.
  ☆77Updated 2 years ago
• sfrwmaker / soldering_907_lcd
  The soldering controller for hakko 907 with lcd screen
  ☆29Updated 5 years ago
• ddrown / stm32-sump
  7.2MHz logic analyzer speaking the SUMP protocol for the stm32f103
  ☆87Updated 4 years ago
• mstrens / grbl_controller_stm32
  Grbl controller running on stm32F103
  ☆35Updated 5 years ago
• LGTMCU / LarduinoISP
  make arduino board to be LGT8FX8D/P programmer
  ☆64Updated 3 years ago
• soguklehim / hot-air-controller
  Hot air rework controller for generic 858D / 8586 / 8858 / 852 / 878 / 858 hot air guns from China.
  ☆31Updated 5 years ago
• megasaturnv / HX-2S-JH20-JH10-reverse-engineered_aka-2S-10A-Balance-Li-ion-Protection-PCB
  Reverse engineered circuit board of the HX-2S-JH20 PCB . Aka 2S 10A w/Balance Li-ion BMS Protection Board.
  ☆35Updated 6 years ago
• danieleff / STM32GENERIC
  Generic implementation of Arduino for STM32 boards
  ☆120Updated 3 years ago
• Upcycle-Electronics / AVR-Transistor-Tester
  ☆44Updated 6 years ago
• baruch / b3603
  Alternative firmware for the B3603
  ☆66Updated 6 years ago
• sfrwmaker / hakko_t12_stm32
  The soldering iron controller built on stm32 micro controller
  ☆157Updated 3 years ago
• maplerainresearch / MRR_ESPE
  MRR ESPE 3D printer control board
  ☆36Updated 5 years ago
• sfrwmaker / F1-T12-858D
  Soldering station for hakko t12 tips + 858D rework
  ☆153Updated last year
• maplerainresearch / MRR_ESPA
  A basic 3D printer control board based on ESP32
  ☆53Updated 5 years ago