Alternatives and similar repositories for ArduinoPLC:

Users that are interested in ArduinoPLC are comparing it to the libraries listed below

• taleswsouza / LadderApp
  Ladder language for programming microcontrollers
  ☆32Updated 4 years ago
• meerstern / SerialPlotter
  The graph drawing software from Serial COM port data
  ☆11Updated 8 years ago
• ciaa / IDE4PLC
  A libre Programming Software for PLC comply with IEC 61131-3
  ☆47Updated 7 years ago
• samuelventura / SharpMaster
  RTU & TCP Modbus Terminal
  ☆26Updated 2 years ago
• briandorey / ModernUI-Pick-and-Place-Controller-Software
  This application is a Windows C# control application to run a DIY pick and place machine via A KFlop motion controller and Windows PC wit…
  ☆21Updated 9 years ago
• thiagoralves / OpenPLC-Neo
  A cheap, reliable, expandable and, of course, open source device that works with OpenPLC software
  ☆22Updated 7 years ago
• terjeio / Grbl_CNC_Controls
  GRBL CNC Controls for GCode Senders written in .NET C#
  ☆29Updated 5 years ago
• andreili / STM32-PLC
  The project is open source and open hardware, the purpose of which is to create a PLC based on STM32 MCU's.
  ☆59Updated 7 years ago
• robincornelius / libCanOpenSimple
  A Simple C# canopen library with access to hardware via canfestival drivers
  ☆25Updated 3 months ago
• nwertzberger / OpenPLC
  OpenPLC is an open source PLC Hardware board. Think Arduino, but change the language used, up the voltage levels, and add a built-in Eth…
  ☆73Updated 6 years ago
• ulrikhagstrom / datalinkengineeringcanopen
  CANopen SDK (API) for Windows developers. Supported adapters: Kvaser, Ixxat, CANUSB, CAN232, Peak PCAN, Copley Controls, USBTIN and more.
  ☆36Updated last year
• shaise / GrblCNC
  A C# Clone to LinuxCNC that works with GRBL CNC driver
  ☆24Updated last month
• darinh / scada
  WPF Scada app
  ☆14Updated 11 years ago
• cpipero / ArduinoLadder
  GUI application to create Arduino programs using ladder logic (like a PLC)
  ☆50Updated 9 years ago
• aiten / CNCLib
  CNCLib - a program to control your Arduino based CNC machine
  ☆42Updated last month
• ethercat-diy / arducat
  EtherCAT over arduino (atmega1280)
  ☆53Updated 6 years ago
• robincornelius / CanOpenMonitor
  A CanOpen Logging and injection tool
  ☆53Updated 3 months ago
• adgzlanl / S7Profinet
  SPS geräte verbindung,Daten Baustein mit Timer Auslesen und Single Parameter Schreiben
  ☆11Updated 6 years ago
• IRNAS / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆36Updated 8 years ago
• hsu-net / NullModemEmulator
  com0com virtual serial port wrapper for C#
  ☆40Updated 2 years ago
• nucleron / beremiz
  ☆67Updated 3 years ago
• fredericdepuydt / profibus-dp-software-stack
  PROFIBUS DP Software Stack
  ☆37Updated 5 years ago
• nm156 / CNCInfusion
  A C# GUI for Grbl
  ☆38Updated last year
• ornothing / BMSTestTool
  This is a test application for NetZero battery management system.
  ☆13Updated 6 years ago
• lipoyang / SOEM4Arduino
  Simple Open EtherCAT Master Library for Arduino
  ☆71Updated 3 years ago
• elliotwoods / Candle.NET
  .NET wrapper for the Candle API for candlelight CAN bus gateways/analysers (e.g. CANable, CANtact, etc)
  ☆24Updated 7 months ago
• nucleron / IDE
  ☆16Updated 5 years ago
• ethercat-diy / stm32f4_ethercat
  ☆30Updated 8 years ago
• ted314 / softPLC_IDE
  A simple IDE where you can write a PLC program, and compile it into a C program which can run on a emmbeding system.
  ☆10Updated 3 years ago
• HilscherAutomation / netPI-openplc
  OpenPLC - Open source IEC 61131-3 compatible PLC
  ☆33Updated 6 years ago