sweetlilmre / TapuinoNextLinks
The evolution of the Tapuino project
☆32Updated 2 years ago
Alternatives and similar repositories for TapuinoNext
Users that are interested in TapuinoNext are comparing it to the libraries listed below
Sorting:
- An easier to solder version of the Lumafix board, components spaced out a bit more to make things easier on the beginner (mostly meaning …☆37Updated 5 years ago
- A PCB build of Rob Smiths Amiga DrawBridge, an Arduino-based solution for reading and writing Amiga floppy disks on modern hardware. Also…☆45Updated last year
- PS/2 to C64 Mouse Adapter☆65Updated 10 years ago
- SRAM substitute for C64C shortboards☆61Updated 7 years ago
- Hardware design of Magic Desk compatible C64 cartridge up to 512k☆74Updated 8 months ago
- Hardware design of Magic Desk and Ocean compatible cartridge for the Commodore 64☆49Updated 8 months ago
- Kernal switcher for the C64/C64C/C128☆100Updated 3 years ago
- Simple PCB for building a XUM1541, a device for copying data to and from Commodore 1541 disk drives using a modern computer.☆34Updated 5 years ago
- Ersetzt den Analogteil einer Floppy 1541 oder 1541-II durch ein µC.☆47Updated 2 years ago
- a tape port storage pod for the C64☆76Updated 3 years ago
- Open Hardware Fast Loader cartridge for the Commodore 64 and 128 - DO NOT USE!!!☆48Updated last year
- Hardware design of a (up to) 2MB cartridge for the Commodore 264 line of computers (Commodore 16, 116 and plus/4)☆28Updated 8 months ago
- A NodeMCU (ESP8266) based WiFi modem for the C64's user port☆85Updated 2 years ago
- Repository for retro computer cartridges☆27Updated 4 years ago
- This is a reliable and easy to build parallel User Port Adapter for the Commodore 1541/1541-II☆26Updated last year
- USB Adaptor for the Joystick and Mouse port of Commodore 64☆41Updated 3 months ago
- SPI adapter that connects to the parallel port of an Amiga☆51Updated 4 months ago
- This is an Enhanced version of the 1581 Drive PCB.☆50Updated last year
- JiffyDOS compatible SATA hard drive interface for the IEC-bus on Commodore's 8-bit computers☆13Updated 3 years ago
- I wanted a Pi1541-module that did not feel like I was handling bare electronics, so I made another that manages to hide most of the scar…☆33Updated last year
- 4MB RAM expansion for Atari 520ST(M)☆44Updated 3 years ago
- An RGB adapter for TMS9928A and TMS9929A☆60Updated 5 years ago
- A simple modulator replacement for Commodore 64s with "longboards", complements my Lumafix version as well adding an audio connector for …☆38Updated 5 years ago
- C64 power supplies are ancient, they go bad every day so use protection!☆41Updated 5 years ago
- A replacement RF modulator for the Commodore 128 and C64 shortboard☆21Updated 2 months ago
- SDBox-v2 for Amiga, compatible with the new updated card-detect firmware☆48Updated 4 years ago
- A replacement RF modulator for the Commodore 64 longboard variants☆23Updated 2 months ago
- It's a tapuino, mostly because I wanted to build one. Uses an Arduino to load tapes on the good old Commodore 64.☆18Updated 3 years ago
- GUI Wrapper for Keir Fraser's Greaseweazle☆22Updated 3 months ago
- Interface to allow Super Nintendo (SNES) control pads to be plugged into a C64's joystick ports.☆39Updated 3 years ago