Alternatives and similar repositories for CartridgeWriter

Users that are interested in CartridgeWriter are comparing it to the libraries listed below

• bvanheu / stratatools
  Stratasys EEPROM tool
  ☆92Updated 5 years ago
• meawoppl / eepromTool-ds2433
  A tool for writing and reading One Wire base ds2433 eeproms.
  ☆35Updated 2 years ago
• DStageGarage / ElectronicThrottleController
  This is an open HW project of Electronic Throttle Controller also known as Drive By Wire.
  ☆50Updated 3 months ago
• speeduino / kicad-parts
  A library of kicad symbols and footprints for parts used across the Speeduino boards
  ☆17Updated last year
• clough42 / electronic-leadscrew
  Lathe electronic leadscrew controller
  ☆334Updated 9 months ago
• Twisted-Fields / rp2040-motor-controller
  A dual channel brushless motor controller based on the RP2040 microcontroller, designed in Kicad.
  ☆395Updated 11 months ago
• Tjeerdie / SPECTRE
  Speeduino compatible engine control unit (ECU) based around black STM32F407VET6 board.
  ☆50Updated last year
• zapta / legacy_stepper_motor_analyzer
  A DYI minimalist hardware stepper motor analyzer with graphical touch screen.
  ☆161Updated last year
• speeduino / Ardu-Stim
  ☆126Updated 4 months ago
• openpnp / openpnp-openbuilds
  An OpenPnP compatible SMT pick and place machine based on OpenBuilds linear motion components.
  ☆226Updated 8 years ago
• speeduino / Hardware
  Official Speeduino hardware designs
  ☆204Updated 9 months ago
• janpom / davega
  Firmware for DAVEga, a device for electronic skateboards that displays data read from VESC based speed controllers.
  ☆57Updated 4 years ago
• CutFreedom / grasshopper
  ☆47Updated 4 years ago
• shamansystems / Cheap-FOCer-2
  Low-Cost Motor Controller based on the VESC 6
  ☆360Updated last year
• KevinOConnor / can2040
  Software CAN bus implementation for rp2040 micro-controllers
  ☆757Updated last month
• pgrady3 / EasyController3
  A simple BLDC motor controller, and the evolution of the EasyController2
  ☆86Updated last year
• teemuatlut / TMCStepper
  ☆563Updated 11 months ago
• MielArrojado / speeduino-ardugauge
  An OLED gauge for the Speeduino ECU. Uses UART (secondary serial) for communication.
  ☆37Updated 2 years ago
• mayrthom / CartridgeWriter_uPrint
  A program to reset the cartridges of the 3D Printers Stratasys uPrint, uPrint+, uPrintSE, uPrint SE+ and HP Designjet 3D.
  ☆22Updated 3 years ago
• tonton81 / FlexCAN_T4
  FlexCAN (CAN 2.0 / CANFD) Library for Teensy 3.x and 4.0
  ☆211Updated last year
• Neumi / ethersweep
  Open Source, easy to use Ethernet connected stepper motor controller. Built in FreeCAD, KiCAD and Arduino.
  ☆542Updated 2 months ago
• pazi88 / STM32_mega
  STM32 based Arduino Mega replacement for speeduino
  ☆98Updated 4 months ago
• CrabLabsLLC / OpenMD
  ☆139Updated 7 months ago
• Hell-Fire / WidebandO2
  An Arduino sketch for controlling a Bosch LSU 4.9 Wideband Lambda sensor with minimal parts
  ☆78Updated 11 years ago
• turboedge / SpeedyBoards
  EMS boards powered by Speeduino
  ☆90Updated 8 months ago
• bdring / 6-Pack_CNC_Controller
  ☆310Updated 2 years ago
• nviennot / reversing-mono4k
  Reverse engineering of the Anycubic Mono 4K
  ☆92Updated 2 years ago
• Rack-Robotics / Powercore-V1.0-Hardware
  CAD & Electronics for Powercore V1
  ☆156Updated last year
• pazi88 / 8Ch-EGT
  8Ch EGT sensor board to be used with aftermarket ECUs
  ☆32Updated last year
• vedderb / vesc-os-pi
  A minimal raspberry pi 3 or 4 image that runs VESC Tool
  ☆30Updated 3 years ago