Alternatives and similar repositories for reversing-mono4k

Users that are interested in reversing-mono4k are comparing it to the libraries listed below

• nviennot / turbo-resin
  Open-source firmware for resin printers
  ☆241Updated 2 years ago
• Andrew-Dickinson / photonic-etcher
  Generate exposure masks for Anycubic printers from PCB Gerbers
  ☆100Updated last year
• IvDm / Z-probe-on-smd-resistors-2512
  Auto bed level strain gage for 3D printer using resistors 2512 instead of strain gauges.
  ☆146Updated 5 years ago
• Rack-Robotics / Powercore-V2.0
  Open-Source wire EDM power supply by Rack Robotics, Inc.
  ☆209Updated last year
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆165Updated 5 months ago
• zapta / simple_stepper_motor_analyzer
  A DYI stepper motor analyzer. This is a new design that is based on Raspberry Pi Pico and users a compact single PCB design. NOTE: The l…
  ☆155Updated 2 years ago
• Rack-Robotics / Powercore-V1.0-Hardware
  CAD & Electronics for Powercore V1
  ☆161Updated 2 years ago
• zapta / legacy_stepper_motor_analyzer
  A DYI minimalist hardware stepper motor analyzer with graphical touch screen.
  ☆163Updated 2 years ago
• 0x23 / MicroManipulator
  An open source low-cost, easy-to-build XYZ Micro-Manipulator platform.
  ☆205Updated 4 months ago
• markniu / PandaCAN
  CAN bus extruder, more resistant to noise,reduce a lot of wires for your 3D printer
  ☆116Updated 2 years ago
• Annex-Engineering / anchor
  Anchor, a Rust Klipper protocol implementation
  ☆77Updated last year
• pyr0ball / pyr0piezo
  An AVR/ARM based piezoelectric sensor for use in ultra-precise applications
  ☆78Updated 3 years ago
• Expatria-Technologies / Flexi-HAL
  Expatria Technologies GRBLHAL and LinuxCNC (and more!) CNC control board.
  ☆97Updated 5 months ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆63Updated 2 years ago
• CAP1Sup / Intellistep
  A rework of the terribly coded firmware from the BTT S42B v2 boards
  ☆43Updated last year
• spoter368 / os3m-firmware
  The firmware that powers the OS3M Mouse MCU!
  ☆98Updated last year
• opulo-inc / paste-extruder
  Paste extruder head for the LumenPnP
  ☆58Updated 3 months ago
• 0x23 / open-air-bearings
  Techniques and software to build, design and simulate air bearings
  ☆56Updated last year
• drspangle / infidel-sensor
  Firmware, mechanical and electrical design files for the Inline Filament Diameter Estimator, Lowcost (InFiDEL).
  ☆199Updated 4 years ago
• pepijndevos / spacefox
  A 6dof diy hid
  ☆189Updated last year
• TheContrappostoShop / Prometheus-MSLA
  The Prometheus MSLA 3D Printer
  ☆297Updated 4 months ago
• spoter368 / os3m-hardware
  All the hardware needed to build your own OS3M Mouse!
  ☆381Updated last year
• TheAntTeam / TheAntFarm
  TheAntFarm is an application that simplifies the PCB creation using CNC machines.
  ☆65Updated last week
• 0x23 / QuietAirCompressor
  A small and quiet air compressor design using 3D printed parts where possible.
  ☆94Updated last year
• ultimachine / Einsy-Rambo
  ☆128Updated 3 years ago
• BoltzRnD / SmartPrintCoreH7x
  STM32H7 based Robust and Open Source 3D Printer Mainboard
  ☆70Updated 3 months ago
• spoter368 / os3m-software
  PC-side software for interpreting and configuring the OS3M mouse
  ☆95Updated 2 years ago
• naikymen / klipper-for-cnc
  Fork of the Klipper 3D-printer firmware, plus features for more general CNC.
  ☆139Updated this week
• vvega007 / Spiral-extruder
  Hub of parts for the spiral extruder
  ☆90Updated 4 years ago
• TheDigital1 / powercore_plus
  This is a Pi Pico-SDK version of the Rack Robotics Powercore FW, with added features, support for GUI, and upgraded sensors
  ☆39Updated 2 years ago