lax-fly / lax-esc
an open source esc driver, somewhat like BLHeli, but coded in C++ and based on 32bit mcu, layer design and module design is applied in this code to make it more readable.
☆34Updated 11 months ago
Alternatives and similar repositories for lax-esc:
Users that are interested in lax-esc are comparing it to the libraries listed below
- DC motor control project with the STM32G4 ESC board☆27Updated 2 years ago
- 电子调速器☆16Updated 3 years ago
- Sensorless Brushless Motor ESC firmware☆34Updated 4 years ago
- 使用C语言结合单片机一步一步实现FOC算法控制BLDC电机 Implementing FOC algorithm step by step to control BLDC motor using C language combined with microcontroll…☆22Updated last year
- PX4 Autopilot Software☆52Updated last month
- 基于ch32v307vct6芯片的无感FOC代码加无刷驱动板原理图☆38Updated 2 years ago
- ☆45Updated 7 years ago
- B站 极客车仔 开源FOC☆36Updated 2 years ago
- ☆50Updated 2 years ago
- Bootloader for stm32f10x,IAP by usart3☆36Updated 5 years ago
- Seasky-ODrive☆106Updated 10 months ago
- FOC Learning☆48Updated last year
- 该驱动板是全N-mos的FOC双路电流环驱动板,超高性价比!资料分享!☆18Updated 3 years ago
- ☆23Updated last year
- ☆13Updated 3 years ago
- STM32HAL库解析CRSF(ELRS)协议☆16Updated last year
- DAP-Link with USB Type-C interface based on stm32f103cbt6☆35Updated 5 years ago
- ☆32Updated last year
- 无刷电机矢量驱动板☆164Updated last year
- 该驱动板支持:霍尔无刷驱动、感应电动势无刷驱动、simpleFOC、直流减速电 机改舵机,多样性功能,性价比高☆58Updated 3 years ago
- FOC Motor Controller☆73Updated this week
- 基于STC15W408的富斯二代接收机☆37Updated 5 years ago
- 这是一个用于学习foc而设计的开发板☆30Updated 4 months ago
- Simulink环境下的JLink驱动模块,用来与MCU高速交互数据。☆29Updated 3 years ago
- 基于AT32F421的多轴电调软件, 从am32分支出来的。只能在at32f421上工作,它是一个120MHz的高性能m4内核mcu。AT32F421 MCU based ESC for MultiRotor only. Forked from AM32, focus on…☆11Updated last year
- 三相直流无刷电机驱动器硬件 | FOC控制算法☆63Updated last week
- 基于USB的离线固件更新器☆23Updated last year
- 纯C语言实现的一个按键驱动,可移植性强,支持单双击、连按、连按释放、长按;采用回调处理按键事件(自定义消抖时间),使用只需3步,1:创建按键,2:按键事件与回调处理函数链接映射。然后周期检查按键。☆17Updated 4 years ago
- 双路FOC驱动器☆30Updated 3 years ago
- Open source hardware - NEMA17 closed-loop stepper motor and driver☆41Updated 5 years ago