Alternatives and similar repositories for FBG5:

Users that are interested in FBG5 are comparing it to the libraries listed below

• dmitry-sorkin / Marlin_FB5_K3D
  Marlin 2.0 for Flying Bear 4S
  ☆51Updated 3 years ago
• oducceu / klipper_configs
  ☆36Updated 8 months ago
• ArtificalSUN / MKS-WIFI_PS_uploader
  Simple G-code file uploader for 3D-printers equipped with MKS-WIFI module
  ☆56Updated 2 years ago
• Sergey1560 / fb4s_howto
  Howto
  ☆78Updated last year
• Technarrus / Klipper_FBG6
  ☆22Updated 2 years ago
• vyacheslav-shubin / shui
  MKS-ROBIN_NANO, MKS-WIFI shui firmware
  ☆99Updated 2 weeks ago
• Andy-Big / Marlin_FB_Reborn
  MarlinRB - 3D Printer Firmware based on Marlin 3D v2.1, for Flyingbear Reborn with MKS Robin Nano v1.1, MKS Robin Nano v1.3, MKS Robin Na…
  ☆23Updated last year
• Skiff2 / SkiffDRO
  Проект самодельного DRO
  ☆27Updated 2 years ago
• dmitry-sorkin / K3D-VOSTOK
  K3D VOSTOK 3D printer
  ☆240Updated 2 years ago
• gotchau / GBot-Tiny-Mark-II
  ☆32Updated 4 months ago
• Tombraider2006 / K1
  creality k1 helpfull manuals for user. config, mods, hacks
  ☆127Updated 2 weeks ago
• dmitry-sorkin / k3d-accuracy-test
  FDM 3D Print accuracy test
  ☆29Updated 2 years ago
• ArtificalSUN / Kcalibrator
  Alternative K-factor calibration pattern generator
  ☆102Updated 2 years ago
• NickRimmer / RedBot
  RedBot 3D Printer
  ☆25Updated 2 years ago
• pavluchenkor / iDryerController
  ☆42Updated 3 months ago
• Sergey1560 / Marlin_FB4S
  Marlin 2.0 for Flying Bear 4S/5
  ☆226Updated last year
• mvbasov / PETCTL
  Another variant of PET Pull (https://3deshnik.ru/forum/viewtopic.php?f=37&t=986) project controller
  ☆30Updated 2 years ago
• xreef / MKS_WIFI_upgrade_with_BeePrint_web_interface
  Firmware for MKS WiFi module from Makerbase with BeePrint Web Interface, tested with Flying Bear Ghost 4/5/6 Reborn Flsun
  ☆73Updated 6 months ago
• Chiffa-C3 / Shark-Extruder
  Экструдер разработанный для замены стандартного на принтере FBG6
  ☆24Updated 2 years ago
• evgs / kross-pi-hat
  RPI/OPI Hat board for FB Ghost6 and Reborn2 touchscreens
  ☆16Updated last year
• FB-G6 / Marlin
  Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin inst…
  ☆79Updated 10 months ago
• FBGhost-community / FBG-Cura-Definitions
  Профиль принтера Glying Bear Ghost 4S для Ultimaker Cura
  ☆20Updated 4 years ago
• dmitry-sorkin / BeMeGe
  BeMeGe extruder is BMG reverse, optimized for 3d printing
  ☆59Updated last year
• evgs / OrangePi3Lts
  ☆13Updated 2 months ago
• chevichelov / Control
  Прошивка для контрольки на Arduino
  ☆13Updated last year
• pscrespo / Morpheus-STM32
  A small 3D printer controller board for use with a "blue pill" STM32F1 generic board. Inspired on http://reprap.org/wiki/SinapTec
  ☆73Updated 5 years ago
• gknapp / ghost6
  FlyingBear Ghost 6 3D Printer notes
  ☆16Updated 7 months ago
• skylandersNFC / NFC-King
  [NFC] It can write all 64 blocks on PN532 V2.0 device with Chinese Magic Cards.
  ☆19Updated 2 months ago
• DeZepTup / ULTI_Klipper_config
  ☆11Updated 3 years ago
• CodeName33 / HardwareRemoteControl
  This is software part for project HardwareRemoteControl. It physically connects two computers and allow one to control another. Any OS on…
  ☆20Updated 3 months ago