Alternatives and similar repositories for SAM3X8E

Users that are interested in SAM3X8E are comparing it to the libraries listed below

• grblHAL / iMXRT1062
  grblHAL driver for NXP iMXRT1062 (Teensy 4.x)
  ☆56Updated this week
• grblHAL / plugins
  Plugins overview
  ☆26Updated 8 months ago
• grblHAL / PostProcessors
  Post processors for grblHAL and Grbl
  ☆13Updated last year
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆121Updated last month
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆55Updated 7 months ago
• RootCNC / Root-Controller-ISO
  ESP32 GRBL Controller for the Root CNC machines
  ☆26Updated last year
• grblHAL / Simulator
  grblHAL drivers for simulation (Linux and Windows)
  ☆36Updated this week
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 8 months ago
• grblHAL / drivers
  Driver overview
  ☆37Updated 8 months ago
• Rack-Robotics / Powercore-V1.0-Firmware
  ☆35Updated 2 years ago
• AlexmagToast / LinuxCNC_ArduinoConnector
  This Projekt enables you to connect an Arduino to LinuxCNC and provides as many IO's as you could ever wish for. This Software is used as…
  ☆90Updated 4 months ago
• Expatria-Technologies / grblhal_2000_PrintNC
  Expatria Technologies GRBLHAL Breakout board for PrintNC
  ☆31Updated 2 years ago
• scottalford75 / LinuxCNC-on-RPi
  ☆29Updated 5 years ago
• fra589 / cn5X
  cn5X++ is a new 5/6 axis Grbl control panel to implement all the grbl-Mega-5X capabilities.
  ☆81Updated last year
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated 8 months ago
• gnea / grbl-LPC
  ☆76Updated 3 years ago
• Macrobase-tech / MKS-DLC32
  MKS DLC32 is 32bit MCU powerful controller for CNC machine.
  ☆55Updated 2 years ago
• kcjengr / probe_basic
  User interface for the LinuxCNC machine control.
  ☆115Updated 3 weeks ago
• ryannining / karyacontroller
  4 axis CNC, 3D, Laser Controller
  ☆63Updated 11 months ago
• bdring / 4_Axis_SPI_CNC
  4 Axis CNC Controller for Grbl_ESP32
  ☆68Updated 5 years ago
• buildbotics / bbctrl-pcb
  Buildbotics CNC, 3D printer and other machine controller
  ☆49Updated 3 years ago
• scottalford75 / Remora
  Remora is a free, opensource LinuxCNC component and Programmable Realtime Unit (PRU) firmware to allow LPC176x and STM32F4 micro-controll…
  ☆164Updated 3 months ago
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆147Updated 2 weeks ago
• grblHAL / ESP32
  grblHAL driver for ESP32
  ☆109Updated this week
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆90Updated 3 years ago
• multigcs / LinuxCNC-RIO
  RealtimeIO for LinuxCNC based on an FPGA
  ☆80Updated last year
• HaleDesign / TorchHeightController
  Arduino based THC that read plasma cutter voltage and send Up and Down signals to Plasma Torch Actuator to adjust voltage to target value…
  ☆47Updated 4 years ago
• jschoch / ESPels
  ESP32 electronic leadscrew for a lathe
  ☆25Updated last year
• ftobler / pick-plaz
  Open source pick and place machine
  ☆26Updated last year
• terjeio / ioSender
  A GCode Sender for Grbl and grblHAL written in C# (Windows only).
  ☆261Updated last month