digant73 / BIGTREETECH-TouchScreenFirmware
support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1, TFT43, TFT50, TFT70
☆42Updated last month
Alternatives and similar repositories for BIGTREETECH-TouchScreenFirmware:
Users that are interested in BIGTREETECH-TouchScreenFirmware are comparing it to the libraries listed below
- Marlin is an optimized firmware for RepRap 3D printers based on the Arduino platform. | Many commercial 3D printers come with Marlin inst…☆33Updated last year
- A tool that generates G-Code for Hotend Benchmarking☆172Updated 8 months ago
- A simple How-To for integrating LEDs with your Klipper/Moonraker machine☆89Updated 2 years ago
- 3D Printed heat press tool for threaded inserts☆127Updated 2 years ago
- Auto power off setup for a Klipper printer☆109Updated 3 weeks ago
- Ultimaker Cura plugin to enable various settings and features specific to Klipper firmware.☆108Updated last year
- A collection of macros common to all my printers running Klipper☆72Updated last week
- FluiddPi - A Pi image with Klipper, Moonraker, Fluidd and Web Camera support pre-installed.☆110Updated 3 years ago
- BIGTREETECH Relay V1.2 is an upgrade of the original (BIGTREETECH V1.0). After upgrading, a small MCU was added on the module to make the…☆129Updated 3 years ago
- This is a repository of BIGTREETECH bootloaders. The originals are stored under the bootloader_bin/backed_up_original_bootloaders/ direc…☆129Updated 2 years ago
- OctoBTT☆160Updated 3 years ago
- This library contains all the open source materials of BIGTREETECH touch screen hardware.☆175Updated 9 months ago
- This is my project to enable serial (UART) connected BigTreeTech-TouchScreens with Klipper by emulating anything it needs with macros.☆28Updated 3 months ago
- Stripped down version of BIGTREETECH-TouchScreenFirmware which only supports ST7920 emulation (Marlin Mode)☆157Updated 2 years ago
- support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1☆37Updated 2 months ago
- ☆71Updated last month
- ☆70Updated last week
- Beta SKR V1.4 firmware for the Prusa MK3s Bear☆76Updated 4 years ago
- Adds a GUI to filament changes and filament runouts for Klipper systems running Mainsail.☆56Updated last year
- DIY WiFi Filament dryer☆157Updated last year
- Power Loss Recovery for Klipper☆85Updated last year
- Custom firmware for the SKR Bear Project. Go through the branches to find a firmware matching your setup.☆79Updated 2 years ago
- This is a customized Marlin repo with firmware for various BIQU 3D printers available. Browse the readme to see if there is something her…☆79Updated 2 years ago
- Wireless Inline Filament Diameter Estimator Low-cost Sensor☆186Updated last month
- This Repo is my personal collection of useful Klipper guides and my printer configs.☆90Updated last year
- to streamline the install or upgrade of KLIPPER & DWC2 front-end for it. With these 2 together no need to use octoprint. I run mine on or…☆55Updated 4 years ago
- Klipper Exclude Object Preprocessor for multiple slicers☆165Updated last year
- RepRapFirmware configuration and macros to drive the Enraged Rabbit Carrot Feeder☆40Updated last year
- ☆73Updated this week
- ☆81Updated 3 years ago