Alternatives and similar repositories for OFFLINE-GRBL-STM32-BLUE-PILL

Users that are interested in OFFLINE-GRBL-STM32-BLUE-PILL are comparing it to the libraries listed below

• TheThomasD / Vigo-16
  Vevor CNC 3018 PRO Vigo-16 GRBL Offline Controller Info & Custom Firmware
  ☆10Updated 7 months ago
• LEKN-TECH / G-Sender
  GRBL Offline Controller
  ☆42Updated last year
• cguerrero1205 / LCD_GRBL
  Offline controller for CNC with GRBL 1.1
  ☆72Updated 4 years ago
• drandrewthomas / ESP32_GRBL_CNC_Wireless_Pendant
  A wireless GRBL CNC pendant project based on the ESP32 micro-controller
  ☆53Updated 4 years ago
• mcu51c51 / standaloneGRBL
  An open source, embedded, high performance CNC laser cutting and engraving controller written in optimized C that will run on a straight …
  ☆15Updated 8 years ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆77Updated last month
• positron96 / cnc3018-offline-controller
  Open-source firmware for popular cnc3018 stm32-based offline controller
  ☆77Updated 10 months ago
• PhamDuyAnh / Arduino_Modbus_LCD_Mach3_01
  Mach3 write to Arduino UNO to view X & Y DRO and read external button via ModBus protocol
  ☆12Updated 6 years ago
• bdring / Grbl_ESP32_Development_Controller
  A CNC controller to use and test Grbl_ESP32
  ☆79Updated 4 years ago
• maplerainresearch / MRR_ESPA
  A basic 3D printer control board based on ESP32
  ☆57Updated 5 years ago
• luc-github / ESP3D-TFT
  ESP3D Firmware for ESP32 based TFT
  ☆47Updated 5 months ago
• pscrespo / Morpheus-STM32
  A small 3D printer controller board for use with a "blue pill" STM32F1 generic board. Inspired on http://reprap.org/wiki/SinapTec
  ☆77Updated 5 years ago
• Expatria-Technologies / PicoBOB
  Low-cost and simple GRBLHAL to MACH3 BOB bridge for Raspberry Pi Pico
  ☆27Updated 6 months ago
• SebG3D / TapePuller
  tape puller/remover for 0816 automatic feeder
  ☆21Updated 6 years ago
• paukstelis / dcservo
  Position control of DC motors
  ☆12Updated 5 years ago
• wagiminator / ATtiny13-TinyTacho
  Simple RPM-Meter
  ☆57Updated 2 years ago
• gcobos / grblesp
  GRBL ported to ESP8266, using up to 8 axis. No arduino involved
  ☆59Updated 4 months ago
• mstrens / grbl_controller_stm32
  Grbl controller running on stm32F103
  ☆37Updated 6 years ago
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆90Updated 3 years ago
• makerbase-mks / MKS-DLC32-FIRMWARE
  The source code of MKS DLC32
  ☆93Updated 2 years ago
• mstrens / grbl_controller_esp32
  grbl controller for esp32
  ☆197Updated 2 years ago
• simon-jouet / ESP32Controller
  ESP32-based 3D printer controller
  ☆130Updated 4 years ago
• Am0k-GIT / STM32F401CCU6_UNI
  CNC 4-axis mainboard based on STM32F401CCU6 for Marlin and GRBL-HAL firmware.
  ☆11Updated 2 weeks ago
• pvico / grbl32
  CNC controller running on the STM32F103 "Blue Pill" board, build and flash on Mac/Linux
  ☆67Updated 3 years ago
• wagiminator / ATtiny85-TinyCharger
  Single-Cell Li-Ion Battery Charger with Monitoring
  ☆63Updated 2 years ago
• avandalen / Spotwelder-controller
  ☆13Updated 5 years ago
• maplerainresearch / MRR_ESPE
  MRR ESPE 3D printer control board
  ☆37Updated 5 years ago
• verser-git / ProbeWizard
  Probe Wizard for Mach3
  ☆32Updated 5 years ago
• xreef / BatteryCapacityTesterArduinoNANO
  Battery tester with arduino, with thermistor to check temperature of power resistance and battery. On version 0.2 now It's possible to se…
  ☆27Updated last year
• mgineer85 / 0816-feeder-firmware
  Firmware for the 0816 automatic 3d printed smt feeder for OpenPnP.
  ☆34Updated 3 years ago