Alternatives and similar repositories for fluidnc-config-files

Users that are interested in fluidnc-config-files are comparing it to the libraries listed below

• MitchBradley / ESP3D-WEBUI
  A Web UI for ESP8266 or ESP32 based boards connected to 3D printers / CNC
  ☆37Updated 2 months ago
• Macrobase-tech / MKS-DLC32
  MKS DLC32 is 32bit MCU powerful controller for CNC machine.
  ☆50Updated last year
• drandrewthomas / ESP32_GRBL_CNC_Wireless_Pendant
  A wireless GRBL CNC pendant project based on the ESP32 micro-controller
  ☆52Updated 4 years ago
• positron96 / ESP32_CNC_Pendant
  A CNC Pendant on ESP32 board, with LCD, WiFi and SD card
  ☆75Updated last year
• bdring / PendantsForFluidNC
  Pendants for controlling FluidNC CNC firmware
  ☆41Updated 2 months ago
• terjeio / GRBL_MPG_DRO_BoosterPack
  Tiva C BoosterPack for GRBL MPG/DRO
  ☆47Updated 3 months ago
• bdring / Grbl_ESP32_MPCNC_Controller
  A Grbl_ESP32CNC Controller for MPCNC
  ☆88Updated 3 years ago
• bdring / FluidDial
  A Pendant for FluidNC CNC Firmware
  ☆59Updated 2 weeks ago
• bdring / fluidterm
  A Serial Terminal for FluidNC
  ☆21Updated 3 years ago
• cguerrero1205 / LCD_GRBL
  Offline controller for CNC with GRBL 1.1
  ☆70Updated 4 years ago
• grblHAL / Controllers
  List of controllers supported by grblHAL
  ☆46Updated 3 months ago
• makerbase-mks / MKS-DLC32-FIRMWARE
  The source code of MKS DLC32
  ☆90Updated last year
• McMax1973 / ELS---Electronic-Lead-Screw
  Electronic lead screw for any type of lathe, using ARDUINO UNO
  ☆22Updated 4 months ago
• Macrobase-tech / CNC-Software
  ☆13Updated last month
• cprezzi / grbl-LPC
  Multiple compiled versions for different boards & machines (under releases)
  ☆58Updated 3 years ago
• LEKN-TECH / G-Sender
  GRBL Offline Controller
  ☆39Updated last year
• bdurbrow / grbl-Mega
  An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on an Arduino Me…
  ☆35Updated 4 years ago
• kachurovskiy / megaels
  Metal lathe electronic lead screw project built on top of Russian-speaking DigitalFeed ELS system by Oleg A. and contributors from ChipMa…
  ☆54Updated 2 years ago
• luc-github / ESP3DLib
  ESP3D library for Marlin and ESP32 boards
  ☆108Updated last month
• MarlinFirmware / U8glib-HAL
  Customized U8glib for use in Marlin 2.0
  ☆48Updated 2 months ago
• grblHAL / drivers
  Driver overview
  ☆35Updated 4 months ago
• HaleDesign / TorchHeightController
  Arduino based THC that read plasma cutter voltage and send Up and Down signals to Plasma Torch Actuator to adjust voltage to target value…
  ☆45Updated 4 years ago
• hobbymachinist / els
  Electronic Leadscrew For Lathe
  ☆61Updated 2 years ago
• phil-barrett / grblHAL-teensy-4.x
  GRBL Header for a Teensy 4
  ☆117Updated last year
• martindb / mpcnc_posts_processor
  MPCNC posts processor for Fusion 360 and Marlin
  ☆64Updated 3 years ago
• kachurovskiy / nanoels
  Electronic Lead Screw for metal lathe
  ☆223Updated 2 weeks ago
• zapta / ble_stepper_motor_analyzer
  A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
  ☆51Updated last year
• grblHAL / ESP32
  grblHAL driver for ESP32
  ☆94Updated this week
• michmela44 / ESP3D-WEBUI
  A Web UI for ESP8266 or ESP32 based boards connected to 3D printers / CNC
  ☆19Updated 4 months ago
• mstrens / grbl_controller_esp32
  grbl controller for esp32
  ☆192Updated 2 years ago