Alternatives and similar repositories for Polar-Coaster:

Users that are interested in Polar-Coaster are comparing it to the libraries listed below

• grblHAL / ESP32
  grblHAL driver for ESP32
  ☆81Updated this week
• FYSETC / FYSETC-E4
  FYSETC Board - The E4 board is a minimal 3D printer control board based on the ESP32 microcontroller from ESPRESSIF, with built-in Wi-Fi …
  ☆61Updated last year
• mstrens / grbl_controller_esp32
  grbl controller for esp32
  ☆184Updated last year
• makerbase-mks / MKS-SERVO42B
  MKS SERVO42B is 3d printer closed loop stepper motor NEMA17 MKS SERVO42 developed by Makerbase that prevents losing steps. CPU is STM32F1…
  ☆172Updated 3 years ago
• Aus3D / RUMBA32
  A powerful 32-bit 3D printer control board.
  ☆70Updated 4 years ago
• maplerainresearch / MRR_ESPE
  MRR ESPE 3D printer control board
  ☆36Updated 5 years ago
• piogrammer / alopPNP
  ☆23Updated 2 years ago
• phil-barrett / PicoCNC
  Raspberry Pi Pico based grblHAL Controller
  ☆144Updated last year
• Smoothieware / Smoothieboard2
  Hardware files for the Smoothieboard v2, and extension boards
  ☆56Updated 8 months ago
• mstrens / grbl_6axis_on_stm32
  grbl_6axis_on_stm32
  ☆59Updated 5 years ago
• gcobos / grblesp
  GRBL ported to ESP8266, using up to 8 axis. No arduino involved
  ☆58Updated 2 years ago
• makerbase-mks / MKS-SERVO42C
  MKS SERVO42C, an upgraded version of MKS SERVO42B, built-in Field-Oriented control algorithm, position/speed/ torque closed-loop, 4 Half…
  ☆161Updated 2 years ago
• SourceRabbit / RabbitGRBL
  Professional grade, 100% GRBL compatible motion control firmware for the ESP32
  ☆48Updated last week
• bdring / 4_Axis_SPI_CNC
  4 Axis CNC Controller for Grbl_ESP32
  ☆62Updated 4 years ago
• simon-jouet / ESP32Controller
  ESP32-based 3D printer controller
  ☆123Updated 3 years ago
• KnightSin / Grbl_Esp32
  A port of Grbl CNC Firmware for ESP32
  ☆40Updated 3 years ago
• pvico / grbl32
  CNC controller running on the STM32F103 "Blue Pill" board, build and flash on Mac/Linux
  ☆60Updated 3 years ago
• makerbase-mks / MKS-DLC
  MKS DLC support grbl firmware, can use Laser mode and CNC mode,support connect MKS TFT24/32/35 and TFT_CNC firmware support lasering and …
  ☆97Updated 3 years ago
• thanh-duyen / TXRX-2.4GHz
  ☆31Updated 4 months ago
• uStepper / uStepperS
  ☆54Updated last year
• mstrens / grbl_controller_stm32
  Grbl controller running on stm32F103
  ☆35Updated 5 years ago
• dungjk / grbl-stm32
  An open source, embedded, high performance g-code-parser and CNC milling controller. This is a port of GRBL 1.1 to STM32F10X target.
  ☆77Updated 2 years ago
• cguerrero1205 / LCD_GRBL
  Offline controller for CNC with GRBL 1.1
  ☆68Updated 4 years ago
• ccadic / The603-200
  One of the most strange Vintage Connected Watch project - 192 LED and ESP32
  ☆101Updated 2 years ago
• grblHAL / RP2040
  grblHAL driver for RP2040/RP2350 (Pi Pico, Pi Pico2 etc)
  ☆131Updated this week
• hackaday3D / marlin_stm32
  stm32 for marlin 1.1.9
  ☆53Updated 5 years ago
• jcchurch13 / Mechaduino-Hardware
  Mechaduino hardware design files. Project logs:
  ☆349Updated 7 years ago
• maplerainresearch / MRR_ESPA
  A basic 3D printer control board based on ESP32
  ☆53Updated 5 years ago
• makerbase-mks / MKS-SERVO42A
  Makerbase MKS SERVO42A NEMA17 closed loop stepper motor Driver CNC 3d printer parts prevents losing steps for Gen_L SGen_L
  ☆54Updated 3 years ago
• simplefoc / SimpleFOCMini
  Small package, low-cost BLDC diver board fully compatible with the simplefoc library
  ☆90Updated 9 months ago