Alternatives and similar repositories for Marlin:

Users that are interested in Marlin are comparing it to the libraries listed below

• ercoleg / BIGTREETECH-TouchScreenFirmware
  support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1
  ☆11Updated 4 years ago
• BlomsD / MPCNC-SKR1.3-TMC2208UART
  Modified Marlin 2.0 firmware for the BigTreeTech SKR1.3 with TMC2208 UART drivers for the MPCNC.
  ☆22Updated 2 years ago
• BlomsD / MPCNC-TFT35-V2.0
  Custom firmware for the BigTreeTech TFT35 V2.0 for use with the MPCNC
  ☆25Updated 4 years ago
• V1EngineeringInc / BIGTREETECH-TouchScreenFirmware
  support TFT35 V1.0/V1.1/V1.2/V2.0/V3.0, TFT28, TFT24 V1.1
  ☆21Updated last year
• darksid3r / OctoPrint-TFT
  A OctoPrint touch interface for TFT touch modules based on GTK+3
  ☆70Updated 4 years ago
• sillyfrog / OctoPrint-Klipper-mjpg-Dockerfile
  A Dockerfile for running OctoPrint Klipper and mjpg in a single container
  ☆25Updated 2 years ago
• Sebastianv650 / Prusa-Firmware
  Firmware for Original Prusa i3 3D printer by PrusaResearch
  ☆12Updated 7 years ago
• manu7irl / klipper-DWC2-installer
  to streamline the install or upgrade of KLIPPER & DWC2 front-end for it. With these 2 together no need to use octoprint. I run mine on or…
  ☆55Updated 4 years ago
• EricHigdon / OctoPrint-RGB_status
  Adds RGB LED support to OctoPrint with the ability to choose effects based on the current status of your printer
  ☆33Updated 4 years ago
• mSarheed / home-assistant-moonraker
  ☆39Updated 3 years ago
• BondtechAB / Bondtech-CR10s
  ☆19Updated 5 years ago
• cp2004 / OctoPrint-WLED
  What could be better than using OctoPrint or WLED? A plugin to use both!
  ☆61Updated 9 months ago
• Allted / Marlin
  Optimized firmware for RepRap 3D printers based on the Arduino platform.
  ☆79Updated 3 years ago
• PrusaOwners / klipper
  Klipper is a 3d-printer firmware
  ☆27Updated 4 years ago
• jneilliii / OctoPrint-UltimakerFormatPackage
  ☆30Updated 2 weeks ago
• V1EngineeringInc / MarlinBuilder
  MarlinBuilder
  ☆71Updated 3 weeks ago
• MirageC79 / FilamentDryer_Controller
  Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.
  ☆37Updated 4 years ago
• CyberSensei1 / OctoPrint-Esp32CamUI
  This plugin will add ESP32-Cam UI to your OctoPrint Interface
  ☆13Updated 2 years ago
• breakingflower / klipper_config
  Klipper profiles for CR10 and CR10s
  ☆73Updated 4 years ago
• prusa3d / Prusa3D-Test-Objects
  Testing and calibration objects/gcodes.
  ☆33Updated 5 years ago
• KAY3D / Marlin
  Absolutely the Easiest Compiling Firmware for RepRap 3D Printers.
  ☆32Updated 4 years ago
• jneilliii / OctoPrint-TasmotaMQTT
  ☆18Updated 11 months ago
• SergiuToporjinschi / OctoPrint-CalibrationTools
  ☆20Updated last year
• flyfisher604 / mpcnc_post_processor
  Marlin/MPCNC posts processor for Fusion 360
  ☆66Updated last year
• pkElectronics / OctoPrint-Octoremote
  A hardware remote for Octoprint controlled 3D Printers
  ☆21Updated 6 years ago
• iFrostizz / OctoPrint-CalibrationCompanion
  This plugin was created to calibrate 3D printer settings easily.
  ☆36Updated 2 years ago
• bradcfisher / OctoPrint-ExcludeRegionPlugin
  OctoPrint plugin that adds the ability to prevent printing within rectangular or circular regions of the currently active gcode file.
  ☆56Updated last year
• gdombiak / OctoPrint-OctoPod
  OctoPod plugin for OctoPrint. Used for sending real time push notifications
  ☆74Updated 3 months ago
• jjgraphix / KlipperSettingsPlugin
  Ultimaker Cura plugin to enable various settings and features specific to Klipper firmware.
  ☆108Updated 2 years ago
• OctoPrint / OctoPrint-MQTT
  An OctoPrint Plugin that adds support for MQTT.
  ☆161Updated 10 months ago