Alternatives and similar repositories for BIGTREETECH-TouchScreenFirmware

Users that are interested in BIGTREETECH-TouchScreenFirmware are comparing it to the libraries listed below

• codiac2600 / SKR-MK3s-V1.4-Beta
  Beta SKR V1.4 firmware for the Prusa MK3s Bear
  ☆76Updated 5 years ago
• codiac2600 / SKR-Bear-Marlin
  Custom firmware for the SKR Bear Project. Go through the branches to find a firmware matching your setup.
  ☆79Updated 3 years ago
• teachingtechYT / SuperSlicer
  ☆100Updated 3 years ago
• BondtechAB / Bondtech-Prusa-Firmware
  Firmware for Bondtech Extruders on Prusa i3 3D printer by PrusaResearch
  ☆28Updated 10 months ago
• bear-lab-3d / Prusa-Firmware
  Bear calibration firmware for Bear extruder 0.7.0-beta and greater based on Prusa Firmware
  ☆55Updated 3 years ago
• teeminus / NoTouchScreenFirmware
  Stripped down version of BIGTREETECH-TouchScreenFirmware which only supports ST7920 emulation (Marlin Mode)
  ☆162Updated 3 years ago
• flyfisher604 / mpcnc_post_processor
  Marlin/MPCNC posts processor for Fusion 360
  ☆69Updated 2 years ago
• breakingflower / klipper_config
  Klipper profiles for CR10 and CR10s
  ☆74Updated 5 years ago
• V1EngineeringInc / MarlinBuilder
  MarlinBuilder
  ☆71Updated 8 months ago
• Caribou3d / CaribouCartesian
  CaribouMK3s and CaribouDuet plastic parts
  ☆149Updated last year
• bigtreetech / BIGTREETECH-Relay-V1.2
  BIGTREETECH Relay V1.2 is an upgrade of the original (BIGTREETECH V1.0). After upgrading, a small MCU was added on the module to make the…
  ☆139Updated 4 years ago
• spooknik / FLAP
  Filament Loading À la Prusa - A set of Klipper macros for filament loading
  ☆48Updated 8 months ago
• looxonline / Marlin
  This is a customized Marlin repo with firmware for various BIQU 3D printers available. Browse the readme to see if there is something her…
  ☆80Updated 2 years ago
• thisiskeithb / PrusaAIO
  All-in-One Marlin firmware for your 32-bit Prusa MK2.5S & MK3S/+ Bear!
  ☆53Updated 2 months ago
• mainsail-crew / sonar
  Sonar is a small Keepalive daemon for MainsailOS.
  ☆95Updated 8 months ago
• EVA-3D / contrib-extras
  Community contributions that do not necessarily conform 100% to the standard EVA defines, but may still be useful in specific application…
  ☆28Updated 3 years ago
• 0ndsk4 / VoronUsers
  Voron Community mods, slicer profiles and firmware configurations.
  ☆141Updated 4 years ago
• strayr / k-macros
  useful macros to extend the functionality of klipper
  ☆165Updated 2 months ago
• bigtreetech / OctoBTT
  OctoBTT
  ☆161Updated 4 years ago
• simplisticton / common-macros
  A collection of macros common to all my printers running Klipper
  ☆75Updated 8 months ago
• cadriel / FluiddPIOLD
  FluiddPi - A Pi image with Klipper, Moonraker, Fluidd and Web Camera support pre-installed.
  ☆110Updated 4 years ago
• bigtreetech / smart-filament-detection-module
  ☆314Updated 2 years ago
• 3dprintingworld / MULDEX
  Muldex - REP-RAP IDEX 3D Printer
  ☆123Updated last year
• MirageC79 / FilamentDryer_Controller
  Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.
  ☆42Updated 5 years ago
• Low-Frequency / Klipper-Git-Backup
  Fully automated klipper backups
  ☆132Updated last year
• bigtreetech / BIGTREETECH-SKR-E3-Turbo
  ☆85Updated 4 years ago
• Gliptopolis / WLED_Klipper
  A simple How-To for integrating LEDs with your Klipper/Moonraker machine
  ☆109Updated 3 years ago
• FYSETC / FYSETC-PortableInputShaper
  Portable Input Shaper(PIS)
  ☆126Updated last year
• vertigo235 / Prusa-Firmware
  Firmware for Original Prusa i3 3D printer by PrusaResearch
  ☆63Updated 3 years ago
• meteyou / KlipperMisc
  This Repo is my personal collection of useful Klipper guides and my printer configs.
  ☆89Updated 2 years ago