Alternatives and similar repositories for ender5-s1_klipper:

Users that are interested in ender5-s1_klipper are comparing it to the libraries listed below

• codiac2600 / SKR-MK3s-V1.4-Beta
  Beta SKR V1.4 firmware for the Prusa MK3s Bear
  ☆77Updated 4 years ago
• LazaroFilm / klipper_config
  Klipper config backups
  ☆13Updated this week
• armysolo / BLV-Cube
  Mods for BLV Cube
  ☆41Updated 2 years ago
• thisiskeithb / PrusaAIO
  All-in-One Marlin firmware for your 32-bit Prusa MK2.5S & MK3S/+ Bear!
  ☆47Updated this week
• Arksine / LPC17xx-DFU-Bootloader
  DFU Bootloader for LPC17xx family
  ☆50Updated 5 years ago
• JJShankles / 3Dprinter_Files
  My files for 3D printer configuration
  ☆20Updated 2 years ago
• printermods / xchange
  XChange printable adapters, firmware, accessories
  ☆67Updated 2 years ago
• MirageC79 / FilamentDryer_Controller
  Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.
  ☆37Updated 4 years ago
• 92jackson / mainsail-advanced-filament-swap
  Adds a GUI to filament changes and filament runouts for Klipper systems running Mainsail.
  ☆55Updated last year
• freakydude / klipper-serial-btt
  This is my project to enable serial (UART) connected BigTreeTech-TouchScreens with Klipper by emulating anything it needs with macros.
  ☆28Updated 2 months ago
• guru-florida / klipper-webcam_focus
  Klipper plugin that uses the machine position to set manual focus on your printer's webcam
  ☆16Updated 9 months ago
• bgdog1 / 3dPrinterCase
  Stand Alone Main Control Case with Modular Mounts for Various Mainboards, Display's, RPi's, Fans amd MORE!
  ☆163Updated last year
• tinntbg / auto-power-off-klipper
  Auto power off setup for a Klipper printer
  ☆109Updated last year
• supermerill / SuperSlicer-Manual
  Documentation for Superslicer
  ☆22Updated 3 years ago
• teeminus / NoTouchScreenFirmware
  Stripped down version of BIGTREETECH-TouchScreenFirmware which only supports ST7920 emulation (Marlin Mode)
  ☆157Updated 2 years ago
• Prutsium / 3D-Druckerplausch-Klipper
  Repo for config file(s) for Prusa MK3(S)(+) with Klipper
  ☆36Updated 2 years ago
• The--Captain / pa_tuner
  ☆22Updated 2 years ago
• GadgetAngel / SKR-V1.4-Turbo-Stepper-Driver-Jumper-Configuration-Manual
  SKR V1.4 TURBO Stepper Driver Jumper Configuration Manual
  ☆38Updated 4 years ago
• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆83Updated last year
• jjgraphix / KlipperSettingsPlugin
  Ultimaker Cura plugin to enable various settings and features specific to Klipper firmware.
  ☆108Updated last year
• bigtreetech / BTT-Expansion-module
  BTT EXP MOT V1.0、BTT RRF WiFi V1.0、BTT EEPROM V1.0
  ☆75Updated last year
• AdamV3D / V-Core-3-Vector3DEdition
  Vector 3D Mods of the Rat Rig V-Core 3 3D Printer with EVA
  ☆50Updated last month
• gab-3d / Gab3d-Klipper-Utilities
  ☆25Updated last year
• SasaKaranovic / DIY-Filament-Dryer
  DIY WiFi Filament dryer
  ☆153Updated last year
• bigtreetech / H2-Series
  ☆46Updated 2 years ago
• codiac2600 / SKR-Bear-Marlin
  Custom firmware for the SKR Bear Project. Go through the branches to find a firmware matching your setup.
  ☆79Updated 2 years ago
• theycallmek / Klipper-Input-Shaping-Assistant
  Run Klipper's input shaping calibration without the need for a full Klipper setup.
  ☆32Updated last year
• rosscon / klipper-macros
  Collection of useful macros for klipper
  ☆10Updated last year