Alternatives and similar repositories for KlipperConfigs:

Users that are interested in KlipperConfigs are comparing it to the libraries listed below

• The--Captain / plr-klipper
  Power Loss Recovery for Klipper
  ☆85Updated last year
• 11chrisadams11 / Klipper-WS281x_LED_Status
  Use WS281x LED strips with Klipper
  ☆52Updated 2 years ago
• gab-3d / Gab3d-Klipper-Utilities
  ☆25Updated last year
• julianschill / moonshine
  Controlling LEDs from Klipper using LED Control from jackw01. This repository contains the needed files and an installation script.
  ☆37Updated 2 years ago
• kermyb123 / 3DPrinting
  ☆19Updated last year
• bumbeng / Klipperscreen_blurry_theme
  A nice theme for Klipperscreen
  ☆14Updated last year
• tinntbg / auto-power-off-klipper
  Auto power off setup for a Klipper printer
  ☆110Updated 2 weeks ago
• freakydude / klipper-serial-btt
  This is my project to enable serial (UART) connected BigTreeTech-TouchScreens with Klipper by emulating anything it needs with macros.
  ☆28Updated 2 months ago
• Gliptopolis / WLED_Klipper
  A simple How-To for integrating LEDs with your Klipper/Moonraker machine
  ☆88Updated 2 years ago
• 3DAixperts / skirt-button-pcb
  ☆42Updated last year
• timmit99 / Klipper-Expander
  ☆43Updated 2 years ago
• 92jackson / mainsail-advanced-filament-swap
  Adds a GUI to filament changes and filament runouts for Klipper systems running Mainsail.
  ☆56Updated last year
• sttts / voron-klipper-config
  Klipper configuration for Voron 2.4
  ☆34Updated last month
• mainsail-crew / sonar
  Sonar is a small Keepalive daemon for MainsailOS.
  ☆87Updated 2 weeks ago
• bigtreetech / HBB
  ☆23Updated 9 months ago
• MirageC79 / FilamentDryer_Controller
  Arduino OLED Rlelay and DS18B20 to control heater element of a 3D printing Filament dryer.
  ☆37Updated 4 years ago
• Stephan3 / Schnitzelslicerrepo
  ☆86Updated 3 years ago
• Clank50AE / Clanks-Klipper-Configs
  Klipper config files for use with Klipper firmware
  ☆87Updated 2 months ago
• alchemyEngine / VoronUsers
  Voron Community mods, slicer profiles and firmware configurations.
  ☆33Updated 4 years ago
• Low-Frequency / Klipper-Git-Backup
  Fully automated klipper backups
  ☆126Updated 6 months ago
• armysolo / BLV-Cube
  Mods for BLV Cube
  ☆42Updated 2 years ago
• breakingflower / klipper_config
  Klipper profiles for CR10 and CR10s
  ☆73Updated 4 years ago
• meteyou / KlipperMisc
  This Repo is my personal collection of useful Klipper guides and my printer configs.
  ☆89Updated last year
• droans / klipper_extras
  Custom Extras for Klipper
  ☆36Updated 2 years ago
• guru-florida / klipper-webcam_focus
  Klipper plugin that uses the machine position to set manual focus on your printer's webcam
  ☆16Updated 10 months ago
• goopypanther / klipper_network_status
  Klipper plugin to make system IP/etc available to macros
  ☆60Updated last year
• boodaah3d / spoolman-install
  ☆11Updated last year
• BlackNet / Voron_2.4
  This is my Voron V2.4r2 350mm config work zone!
  ☆4Updated this week
• bigtreetech / BIGTREETECH-Relay-V1.2
  BIGTREETECH Relay V1.2 is an upgrade of the original (BIGTREETECH V1.0). After upgrading, a small MCU was added on the module to make the…
  ☆129Updated 3 years ago
• rkolbi / voron2.4
  A collection of Klipper related things
  ☆98Updated last month