Alternatives and similar repositories for The-Ultimate-Filament-Tuning-Guide

Users that are interested in The-Ultimate-Filament-Tuning-Guide are comparing it to the libraries listed below

• MapleLeafMakers / klipper-virtual_leds
  Virtual LED chains composed of segments of physical led chains... for klipper.
  ☆19Updated last year
• CODeRUS / klipper_web_builder
  Simple Klipper Firmware Builder
  ☆15Updated 4 months ago
• SnakeOilXY / klipper-extended-corexy-kinematic
  Klipper module for extended-corexy kinematic
  ☆29Updated 6 months ago
• NedalLive / Hypercube-NGen
  Hypercube NGen 3D Printer
  ☆18Updated 3 years ago
• 3DPrintingMods / KIC_Steppers_Motors
  Water Cooling blocks for Nema 17s and 14s, with M5 Pneumatic fittings.
  ☆16Updated last year
• K-Tett / Klipper-FastSQV
  A post-processing script and macro to accelerate the perimeter and infill print speed with Klipper
  ☆31Updated 2 years ago
• FaqT0tum / Skewder_Servo_Extruder
  Axial Rotation Servo Extruder
  ☆28Updated 2 months ago
• xbst / PiCAN
  A compact, USB drive shaped USB to CAN bus adapter
  ☆22Updated 10 months ago
• Project-R3D / Z-Brake-Board
  Reference and fab files for the Project R3D Z Brake Board
  ☆20Updated 3 years ago
• RobertLorincz / Orbiter-Toolboards
  ☆57Updated 3 weeks ago
• robthide37 / components
  a3dp modular
  ☆13Updated 10 months ago
• xbst / Nevermore-Sensors
  A compact PCB with SGP40 and BME280 sensors wired in I2C mode and powered with 3.3V.
  ☆30Updated last year
• Annex-Engineering / Constellation
  a series of control boards from ANNEX Engineering
  ☆23Updated last year
• MapleLeafMakers / V0_Upper_Rear_Bowden_Inlet
  A Reverse Bowden Inlet for the upper-rear panel of the Voron Zero.
  ☆46Updated last year
• DanniDesign / Ploxy
  Ploxy is an advanced Klipper-powered pen plotter that takes precision and creativity to a whole new level.
  ☆41Updated 4 months ago
• JupaCreations / Belt-Balance-System
  CoreXY 3D printer 200-300-400 XYZ build volume
  ☆12Updated 2 years ago
• Deutherius / Gantry-bowing-induced-Z-offset-correction-through-relative-reference-index
  A guide on how to minimize inconsistent Z offset caused by gantry bowing on klipper machines, particularly Voron 2.4/Trident
  ☆21Updated 3 years ago
• alchemyEngine / klipper
  Klipper is a 3d-printer firmware
  ☆19Updated 5 months ago
• Minsekt / Unclid
  a printable (replacement) combination of unklicky/slideswipe and euclid probe
  ☆41Updated 3 years ago
• comradef191 / NyoomiesKME
  A pico or STM32 powered expansion board for Klipper, with support for four motors running in SPI or UART, and ability to run higher curre…
  ☆24Updated last year
• PoopyPops / Hevoron
  I had a Hypercube. And then I didn't want a Hypercube anymore so now it's a Voron inspired project. Basically I'm just copying Voron part…
  ☆15Updated 3 years ago
• ruiqimao / SugarCube
  Compact CoreXY 3D Printer
  ☆56Updated 2 months ago
• tehmaze / PowerBRRR
  48V injection daughter board for Step Stick drivers
  ☆39Updated 3 years ago
• RealDeuce / Voron-MKS-Monster8
  Files to install a Makerbase MKS Monster8 in a Voron v2.4
  ☆11Updated last year
• TypQxQ / KTC
  Klipper Toolchanger Code v.2
  ☆60Updated 7 months ago
• selliott79 / Voron-V2-Umbilical-Mounts
  Umbilical mounting system for the V2 that doesn't require de-term/ re-term
  ☆17Updated 4 years ago
• altzbox / Chopper-tuning-guide
  ☆27Updated last year
• nevermore3d / Nevermore_FLEX
  Multi printer recirculation filter and solder fume extractor!
  ☆32Updated 2 years ago
• Maverick-3D / Smol_Stealth_Burner
  ☆15Updated 3 years ago
• arsi-apli / BLDC_Klipper_doc
  This is documentation for a modified version of the Klipper firmware that allows you to directly drive a BLDC Motor in an open loop confi…
  ☆19Updated 3 years ago