Alternatives and similar repositories for OpenFan-Micro

Users that are interested in OpenFan-Micro are comparing it to the libraries listed below

• galacticstudios / Logic-Meter
  ☆43Updated 5 years ago
• EmanuelBender / HEX_POD
  Multi-sensor intelligent environmental Monitor
  ☆18Updated last year
• Mew463 / esp32-caliper
  ☆52Updated last year
• hatlabs / SH-RPi-hardware
  Sailor Hat for Raspberry Pi hardware design files
  ☆53Updated last year
• rin67630 / Drok-Juntek-on-steroids
  Extend the possibilities of cheap digital power supplies with a WiFi module
  ☆60Updated last year
• omarkhorshid / OpenRad
  Introducing OpenRad, a simple radiation monitoring solution powered by the SBM-20 GM tube and TTGO ESP32 microcontroller. this project of…
  ☆59Updated last month
• Matthias-Wandel / caliper-interface
  Connecting cheap digital calipers to Raspberry Pi and decode readings
  ☆124Updated 11 months ago
• knifter / DualPID
  Multi Channel Configurable PID regulator on M5Stack Core
  ☆51Updated last year
• SeryDesigns / Battery-Charger
  Li-Ion battery charger, based on BQ24060 IC
  ☆45Updated 2 years ago
• atc1441 / ATC_stc_solder_iron
  Custom firmware for cheap STC Based Soldering iron using PlatformIO and SDCC 8051 based
  ☆51Updated 2 years ago
• oxullo / uctester
  Ultimate Continuity tester
  ☆31Updated 5 years ago
• frank26080115 / Hydra-Dual-Brushed-Motor-ESC
  Dual brushed motor ESC firmware compatible with brushless motor ESCs
  ☆33Updated last year
• joao-pinheiro / atx_psu
  DYI ATX PSU
  ☆36Updated 3 years ago
• dobrishinov / PowerLinkESP
  Enhancing Nice-Power Bench Power Supplies with ESP8266 Connectivity
  ☆68Updated last year
• BEEMB / Battery-Health-Monitor
  Battery Health Monitor A compact device for monitoring the State of Health (SoH) and State of Charge (SoC) of lithium batteries. It uses …
  ☆32Updated 10 months ago
• MariusHeier / magik_solder_paste_stencil_box
  Is it magik? Or is it just a 3d printed box for holding your solder stencils with automatic lifting and vacuum hold down?
  ☆35Updated 4 years ago
• TheMariday / bappr
  Design files for the BAPPR LED buck converter
  ☆43Updated 3 weeks ago
• jfedor2 / magellan-spacemouse
  Adapter to use RS-232 Magellan/SpaceMouse with modern software
  ☆50Updated last month
• rallekralle11 / Epi_4L
  4 layer version of the Epi 32U4
  ☆58Updated 2 years ago
• polihedron / DIY-Reflow-Oven
  DIY Reflow Oven, mcu: STM32F103 dev board, Display: Nextion Basic 3.5", PID controller.
  ☆43Updated 4 years ago
• Connaxio / espoir
  A PoE+ mikroBUS mainboard based on the ESP32
  ☆53Updated 4 months ago
• upiir / arduino_tpms_tire_pressure
  Arduino TPMS - Tire Pressure Monitoring System
  ☆121Updated 6 months ago
• kirberich / gerber_to_scad_service
  Simple django project to allow converting gerber files to 3d printable scad solder stencils
  ☆11Updated 9 years ago
• DurandA / reflow946
  Bluetooth LE temperature controller for the 946C electronic hot plate
  ☆113Updated last year
• dronecz / ESP32-Reflow-Controller
  Reflow controller with ESP32 and TFT LCD on board.
  ☆69Updated 7 months ago
• alunmorris / Multi-channel-autorange-OLED-voltmeter
  Minimalist 4-channel 0 to 27V meter using AVR microcontroller and 72x40 OLED display
  ☆20Updated last year
• liba2k / VINCA_reader
  ☆55Updated last year
• MangyDogUK / ReflowOven
  The source code for my reflow oven, WARNING use at your own risk. This project deals with MAINS VOLTAGES which can kill.
  ☆23Updated 5 years ago
• JGAguado / Smart_Powermeter
  The Smart Powermeter is powered by a ESP32-S2, allowing the measurement up to 6 CT clamps for reading electric current and real-time disp…
  ☆93Updated 9 months ago
• MicroKnotDevelopment / ESP32-Transmitter
  ☆14Updated 3 years ago