Alternatives and similar repositories for STM32GENERIC

Users that are interested in STM32GENERIC are comparing it to the libraries listed below

• IRNAS / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆36Updated 9 years ago
• DAlexis / stm32-usb-bootloader
  This repository contains bootloader for stm32f1xx microcontrollers. It works for stm32f103ret6, but you can simply adopt it to any MCU su…
  ☆48Updated last year
• MaxwellXyao / GRBL-0.8c-for-STM32
  GRBL0.8c移植于stm32,已调式通过
  ☆36Updated 8 years ago
• ManuLST / Marlin4ST
  A Marlin FW for the ST Microelectronics 3D printer board STEVAL-3DP001V1
  ☆106Updated 8 years ago
• danieleff / STM32GENERIC
  Generic implementation of Arduino for STM32 boards
  ☆121Updated 3 years ago
• huaweiwx / sduino
  An Arduino-like programming API for the STM8
  ☆13Updated 7 years ago
• ddrown / stm32-sump
  7.2MHz logic analyzer speaking the SUMP protocol for the stm32f103
  ☆88Updated 4 years ago
• x893 / CNC-STM32
  STM32 based CNC controller
  ☆105Updated 10 years ago
• nichtgedacht / mini-sys
  STM32F103C8, ST7735 based LCD, SD-card, ADC, USBCDC, MPU-9250, S-Bus, Servo control
  ☆16Updated 7 years ago
• ads830e / grbl1.1f-stm32f103c8
  grbl1.1f for stm32f103c8
  ☆20Updated 5 years ago
• deadsy / grbl_stm32f4
  The grbl g-code interpreter ported to the STM32F4
  ☆62Updated last year
• WeActStudio / ArduinoCore-AT32F4
  ☆35Updated last year
• OpenNuvoton / N76E003-BSP
  BSP for N76E003 Series 8051 MCU
  ☆46Updated last year
• VeiLiang / BoloPi_PCB
  F1C100s BoloPi / PineapplePi PCB
  ☆49Updated 4 years ago
• langwadt / grbl_stm32
  grbl for stm32 with nucleo stepper drivers
  ☆33Updated 3 years ago
• dungjk / grbl-stm32
  An open source, embedded, high performance g-code-parser and CNC milling controller. This is a port of GRBL 1.1 to STM32F10X target.
  ☆79Updated 2 years ago
• solosky / stlink-uart
  串口和stlink二合一调试工具。
  ☆97Updated 8 years ago
• hyperstepper / NEMA17-HyperStepper
  Open source hardware - NEMA17 closed-loop stepper motor and driver
  ☆41Updated 5 years ago
• Meekdai / STM32-GRBL
  STM32 CNC Controller （GRBL v0_8）
  ☆105Updated 9 years ago
• ads830e / stm32f030-vusb
  Use gpio to emulate usb low-speed on stm32f030f4p6.Use internal rc instead of crystal.
  ☆34Updated 8 years ago
• sqqdfny / WPC_QI_5W_001
  基于新唐N76E003的5W无线充方案
  ☆19Updated 6 years ago
• LGTMCU / LarduinoISP
  make arduino board to be LGT8FX8D/P programmer
  ☆66Updated 3 years ago
• helimp / grbl_stm32
  GRBL for STM32 controller. Reference: https://github.com/usbcnc/grbl
  ☆20Updated 5 years ago
• technosar / GRBL_STM32
  An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on a straight ST…
  ☆28Updated 4 years ago
• x893 / STM32F103-DualCDC
  STM32F103 Dual CDC
  ☆65Updated 12 years ago
• mstrens / grbl_controller_stm32
  Grbl controller running on stm32F103
  ☆36Updated 6 years ago
• kehribar / lcdMenu
  Portable text based lcd menu library written in C.
  ☆19Updated 11 years ago
• xjtuecho / UIMeter
  high precision voltage, current, temperature meter and logger.
  ☆43Updated 2 years ago
• KnightSin / Grbl_Esp32
  A port of Grbl CNC Firmware for ESP32
  ☆41Updated 3 years ago
• fancy3013 / NRF24L01_WriessUart
  使用时最好关闭ACK，否则假如对方不支持应答会导致工作不正常
  ☆10Updated 10 years ago